Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame rails
Muffler
Hitch Shown In Proper Position
Equipment Required: Phillip's head screwdriver,
Lubricant or Soapy water
Fastener Kit: 36465F
Wrenches: 10mm, 12mm, 17mm, 11/16"
Remove exhaust rubber
isolator front of muffler.
1
Qty. (2)
Hex bolt M10 X 1.25 X 40mm CL8.8
2
Qty. (2)
Conical washer
3
Qty. (1)
U-Bolt 3/8-16
1.
Lower exhaust rubber isolator front and rear of muffler. Remove (2) nuts holding rear muffler hanger. Note: Spraying a lubricant or soapy
water on the metal hanger rod and the rubber isolator helps removal.
2.
Remove appearance panel which covers the trunk pan (for ease of hitch installment). Remove the (4) plastic rivets that fasten the fascia tabs
to the vehicle. Note: Remove the center of the rivet with a screwdriver. Rivets to be reinstalled.
3.
Hang U-bolt on tow hook
4.
Slide hitch up over exhaust tips and align hole in side arm of hitch with weld nuts in vehicle frame as shown in above.
5.
Re-install appearance panel.
6.
Loosely install U-Bolt
7.
Tighten all fasteners to torque specifications.
8.
Raise exhaust system back into position.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2007 Cequent Towing Products
Installation Instructions
Drawbar Kit:
36061
Drawbar must be used in the
RISE position only.
Frame rail
Remove (2) nuts
holding rear muffler
hanger.
Tighten all 3/8 GR2 fasteners with torque wrench to 20 Lb.-Ft. (27 N*M)
Tighten all M10 CL8.8 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M)
Kia Amanti
Do Not Exceed Lower of Towing Vehicle
3500 LB (1589 Kg) Max Gross Trailer Weight
300 LB (136 Kg) Max Tongue Weight
Wiring Access Location: PC3,4
Muffler
3
4
5
6
4
Qty. (2)
Flat washer
5
Qty. (2)
Lock washer
6
Qty. (2)
Hex nut 3/8-16
Sheet 1 of 3
Part Numbers:
Manufacturer's Rating or
1
2
Existing
weld nut
Note: Fasteners typical
both sides
Heat shield, exhaust hangers and
wheel well not shown for clarity.
36465N
10-19-07
36465
90170
06607
Rev. X
Publicidad
Manuales relacionados para Cequent Towing Products 36465
Resumen de contenidos para Cequent Towing Products 36465
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 36465N 10-19-07 Rev. X 2007 Cequent Towing Products...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 of 3 36465N 10-19-07 Rev. X 2007 Cequent Towing Products...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 of 3 36465N 10-19-07 Rev. X 2007 Cequent Towing Products...