Cleaning Detergent Siphoning Tube - Craftsman 580.752090 Manual Del Operador

To apply detergent follow these steps:
1. Review ProjectPro nozzle and HydroFoam™ launcher use.
®
2. Prepare HydroFoam™ wash according to instructions on
the bottle or prepare detergent solution as required by job.
3. Place small filter end of detergent siphoning tube into
detergent container.
NOTE: Make sure the filter is fully submerged in detergent
while applying detergent.
NOTICE
Contact with the hot muffler can damage detergent
siphoning tube.
• When inserting the filter into a detergent solution bottle, route the
tube so as to keep it from inadvertently contacting the hot muffler.
4. Make sure HydroFoam™ Launcher is installed.
NOTE: Detergent cannot be applied with the high pressure
nozzles (Yellow, Orange or Red).
5. Make sure garden hose is connected to water inlet.
Check that high pressure hose is connected to spray gun
and pump. Turn on water.
NOTICE
You must attach all hoses before you start the engine.
• Starting the engine without all the hoses connected and without
the water turned ON will damage the pump.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
6. Start engine following instructions How to Start Your
Pressure Washer.
7. Apply HydroFoam™ wash to a dry surface, starting at
lower portion of area to be washed and work upward,
using long, even, overlapping strokes.
NOTE: To prevent water spotting on vehicles, work in a
shaded area and allow surfaces to cool before beginning.
8. Allow HydroFoam™ wash to soak in between
3–5 minutes before washing and rinsing. Reapply as
needed to prevent surface from drying. DO NOT allow
HydroFoam™ wash to dry on (prevents streaking).
For best results, scrub the HydroFoam™ wash covered
surface to help remove stubborn dirt, grime and stains. For
vehicles, use a soft car wash brush or mitt. For decking,
siding and concrete, use a brush appropriate for the type of
surface being cleaned.
IMPORTANT: You must flush the detergent siphoning system
after each use by placing the filter into a bucket of clean water,
then run the pressure washer in low pressure for 1-2 minutes.
Pressure Washer Rinsing
After HydroFoam™ wash is applied, scour the surface and rinse
it clean as follows:
1. Remove HydroFoam™ Launcher from nozzle extension.
2. Select and install desired ProjectPro
described in How to Use ProjectPro
3.
• Operate pressure washer from a stable surface.
• Be extremely careful if you must use the pressure washer from
• Firmly grasp spray gun with both hands when using high
4.
5.

Cleaning Detergent Siphoning Tube

If you used the detergent siphoning tube, you must flush it
with clean water before stopping the engine.
1.
2.
3.
4. Flush for 1-2 minutes.
5. Shut off engine following instructions How to Stop
6. ALWAYS point spray gun in a safe direction, press red
IMPORTANT: Spray gun traps high water pressure, even
when engine is stopped and water is disconnected.
• Keep high pressure hose connected to reel and spray gun while
• ALWAYS point spray gun in safe direction, press red button
Automatic Cool Down System (Thermal Relief)
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the spray gun,
circulating water in the pump can reach temperatures above
125°F. The system engages to cool the pump by discharging
® nozzle, as the warm water onto the ground.
® Nozzle System.
16
Keep spray gun a safe distance from spray surface.
WARNING
Kickback from spray gun can cause you to fall.
a ladder, scaffolding, or any other similar location.
pressure spray to avoid injury when spray gun kicks back.
Apply a high pressure spray to a small area and then
check the surface for damage. If no damage, proceed to
step 5.
Start at top of area to be rinsed, working down with
same overlapping strokes used for cleaning.
Place detergent siphoning tube/filter in a bucket full of
clean water.
Remove high pressure nozzle from nozzle extension.
Select and install black detergent nozzle following
instructions How to Use ProjectPro
Pressure Washer and turn off water supply.
button and squeeze spray gun trigger to release retained
high water pressure.
WARNING
The high pressure stream of water that this
equipment produces can cut through skin and its
underlying tissues, leading to serious injury and
possible amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected,
which can cause injury.
system is pressurized.
and squeeze spray gun trigger, to release high pressure, every
time you stop engine.
® Nozzle System.