Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
rated residual operating current not exceeding 30 mA.
FR
•
Means for disconnection having a contact separation in all poles must be
incorporated in the xed wiring in accordance with the wiring rules.
ES
•
Regarding the information for the installation and the connection of the
appliance, please refer to the relevant paragraphs below.
PT
•
Concerning installation information, please refer to the chapter<<
Installation>> and <<Fixation of the appliance on the wall>>.
IT
EL
2. INSTALLATION
PL
RU
Connect the two conductors of the supply cable to a connection box in
respecting the polarities as below:
UA
- Live: Brown
- Neutral: Blue
RO
Warning: this product shall be installed in the volumes 2 only according
the national wiring rules (For France NF C 15-100).
EN
Note: We suggest that you to contact a professional electrician for assistance.
Fixation of the appliance on wall
1.
Choose a wall on which there is enough space:
2.
Use a Φ6 drill to drill 6 holes according to following positions:
3.
Fit the pegs from the accessory bag in these holes.
4.
Detach the up-hook from the back of the appliance and put it in the position
of the ve pegs at the bottom. Fix the up-hook on wall with ve ST4X35
screws.
5.
Hang the appliance on wall with a ST4X35 screw on the peg above.
6.
Tighten four M5X12 screws on the right side and one ST4X12 screw on the left
side to x the appliance.
63
3. INSTRUCTION FOR USE
When the product is plugged and push the ON/OFF (0/I) button located at the back of the
appliance,the buzzer "beeps" and the screen ashes for 3s, then in the standby mode. Push
again, if you want to switch o .
In standby mode,you can set the day and time.
SET THE CURREN DAY
Press SET, the day icon （1 2 3 4 5 6 7） ashes. Use + and - to set current day. Then press OK,
it will save and enter into next step automatically for hour setting.
SET THE CURREN HOUR
The hour icon 01:00 ashes. Use + and - to set hour. Then press OK, the minute icon
00:01 ashes. Use + and - to set minutes. In the end ,press OK to con rm and save automatically.
Manual mode:
Press
,start at 2000W (show
on screen), you can do the following:
1) SET TEMPERATURE
Press SET, setting temperature ashes 20 (default temperature setting is 20°C), use + and - to
set and press OK to con rm(selected temperature range 5°C - 40°C).
2) CHANGE POWER
In Manual mode, press
to set the power in following order: 2000W(
-Fan (
). Press again, the power changing will repeat the cycle.
Window mode(ONLY work during manual program):
Press
to turn on open-window detection:
During open-window detection mode,once the ambient temperature drops 5-10℃ within 10
minutes, then the product will stop working within 30 minutes and enter into stand by mode.
Press the
button again to turn o open-window detection.
WEEKLY PROGRAM SETTING (PROGRAM MODE)
Weekly program explain:
1. It can set day by day from Monday to Sunday. And for each day, it can set 2 working periods
(P1/ P2).
2. The product works at full power(2000W) during weekly program.
3. Body sensor only works in weekly program if turn on.
WEEKLY PROGRAM SETTING:
In STANDY MODE: Press
for 3 seconds, it enters into WEEKLY PROGRAM setting,the icon
ashes on the screen until complete the whole setting. And the day icon (1 2 3 4 5 6 7) ashes,
FR
ES
PT
IT
EL
PL
RU
UA
RO
EN
)-1000W(
)
64
Publicidad
Tabla de contenido
