ROBLIN Actis Electro 5741 Instrucciones De Instalación E Utilización página 10

Ocultar thumbs Ver también para Actis Electro 5741:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 24
GB
Starting in the recycling mode (the contaminated air passes into the hood through the grease filters and
the purifying activated charcoal filter and back out into the kitchen through grilles).
Press the '+' button (while the motor and lights are switched 'OFF') until the five LED lights will flash twice
to indicate confirmation that the cooker hood is in the recycling mode.
Reverting to the extraction mode (The cooker hood is ducted to the outside).
Press the '+' button (while the motor and lights are switched 'OFF') until the five LED lights will flash once
to indicate confirmation that the cooker hood is in the extraction mode.
GB
B - BASIC INSTRUCTIONS
Lighting
Press LED button 1 to switch 'ON' the lights and the LED will illuminate to confirm the lights are switched
'ON'.
Motor
Press LED button 2 to switch 'ON' the fan motor (and adjust the speed of the fan motor by pressing the
LED button '+' and '-') and the LED lights 2, 3 and 4 will illuminate. The fan speed will be increased if
constant pressure is kept on the (+) button.
LED 2
: Minimum speed - cooking with one pan or simmering
LED 2 & 3
: Medium speed - normal cooking with up to 4 pans
LED 2, 3 & 4 : Maximum speed - frying and cooking foods with strong odours
Press LED button 5 to obtain the boost position for maximum effect and the LED will illuminate to confirm
fan is switched 'ON'.
C - COMPLEMENTARY INSTRUCTIONS
• Boost speed :
To obtain the best performance it is advisable to switch 'ON' the cooker hood a few minutes (in the boost
setting) before you start cooking. To program the complementary function, proceed as follows:
- Press LED button 2 to switch 'ON' the fan motor and adjust the speed of the fan by pressing the LED
button '+' and '-'. You should keep applying pressure to the '+' and '-' button until the required speed is
selected.
- Press LED button 5 (boost speed) to switch 'ON' the fan motor in the boost setting. Press LED button 5
to switch 'OFF' the boost setting immediately.
It is advisable too that you should leave it running in the boost setting for approximately 5 minutes after
finishing.
• Pre-set stop of the boost speed :
A pre-set stop after 5 minutes of the boost speed is available.
Your cooker hood is supplied with a deactivated pre-set stop of the boost speed. To use the cooker hood
with a pre-set stop of the boost speed re-programme the hood as follows:
The lights and the fan motor should be switched 'OFF' to set the timer.
Push the LED button '-' until the LED lights will flash :
One flash of the LED lights 2,3, and 4 = function is switched 'OFF'.
Two flashes of the LED lights 2,3, and 4 = function is switched 'ON'.
While the 5 minutes timer is running, It is available to stop immediately the boost speed by pressing the
led button 5.
While the 5 minutes timer is running, the indication of saturation of the filters is switched 'OFF'.
If a pre-set stop for the hood is switched 'ON' and the 5 minutes timer is still running, the boost speed will
be switched 'OFF' together with the pre-set stop for the hood after the count down of 5, 10 or 15 minutes.
It is available to stop the boost speed before the count down of the preset stop of the hood by pressing
the led button 5.
• Pre-set stop for the hood :
This function allows you to program the cooker hood to automatically stop cooking after a pre-set period.
8

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Actis electro 7741

Tabla de contenido