Descargar Imprimir esta página

Kichler 4U Serie Manual Del Usuario página 4

Publicidad

Idiomas disponibles

Idiomas disponibles

INSTALLATION INSTRUCTIONS USING PLUG-IN CORD
1.
Hold the fixture in the desired mounting location, leaving approximately 2 ½"
clearance for plug-in cord, and not more than 5' from the nearest outlet.
Drive mounting screws into cabinet surface until fixture is secure. If screws
are difficult to install, mark holes and drill 1/16" maximum pilot holes. (ref. FIG. 5)
NOTE: For 22" and 30" fixtures, open wire compartment by inserting flathead
screwdriver into the slots and wedging cover open to install center screw.
Once installed, swing the cover towards the fixture and close it by pressing at
the ends of the cover until the cover snaps into place and is flush with the fixture.
2.
Connect cord into fixture female connector.
CAUTION: Never connect the plug-in cord to a fixture or system that is
already energized
3.
Peel backing off retaining clip(s) and affix to desired location(s). Surface
should be as clean as possible.
4.
Slip cables into clip(s) and snap closed.
5.
If this will be an end fixture in a run, use connector cover over any connector
not being used.
6.
Plug cord into outlet.
INSTALLATION INSTRUCTIONS USING INTERCONNECT CABLE
1.
Turn off power.
2.
Hold the fixture in the desired mounting location, not more than 21" from
nearest interconnected fixture, allowing approximately 2 ½" clearance for
interconnect cables. Drive mounting screws into cabinet surface until fixture
is secure. If screws are difficult to install, mark holes and drill 1/16" maximum
pilot holes. (ref. FIG. 6)
NOTE: For 22" and 30" fixtures, open wire compartment by inserting flathead
screwdriver into the slots and wedging cover open to install center screw.
Once installed, swing the cover towards the fixture and close it by pressing at
the ends of the cover until the cover snaps into place and is flush with the fixture.
3.
Connect fixture to existing Kichler Cabinet Lighting system using interconnect
cable.
4.
Hold interconnect cable to mounting surface and determine best path for
cable. If interconnect cable is being run from cabinet to cabinet a notch such
as a "V" could be cut in cabinet side panels to help keep cables out of site.
NOTE: Interconnect cable is not intended for use through or concealed
behind walls, floors or ceilings.
5.
Peel backing off retaining clip(s) and affix to desired location(s). Surface
should be as clean as possible.
6.
Slip cables into clip(s) and snap closed.
7.
If this will be an end fixture in a run, use connector cover over any connector
not being used.
8.
Turn on power.
INSTALLING FIXTURE TO FIXTURE
1.
Turn off power.
2.
Align connector on end of new fixture with connector on end of existing fixture.
3.
Push new fixture to existing fixture until fixtures are flush and connectors
snap together.
4.
Drive mounting screws into cabinet surface until fixture is secure. If screws
are difficult to install, mark holes, remove fixture and drill 1/16" maximum pilot
holes. (ref. FIG.7)
NOTE: For 22" and 30" fixtures, open wire compartment by inserting flathead
screwdriver into the slots and wedging cover open to install center screw.
Once installed, swing the cover towards the fixture and close it by pressing at
the ends of the cover until the cover snaps into place and is flush with the fixture.
5.
If this will be an end fixture in a run, use connector cover over any connector
not being used.
6.
Turn on power.
INSTALLING REPLACEMENT POWER SUPPLY
1.
Turn off power.
2.
Open wiring compartment by inserting flathead screwdriver into the slots and
wedging cover open. (ref. FIG. 8)
3.
Identify the power supply leads and remove the corresponding wire nuts. Set
aside.
4.
Unscrew the wing nut to remove the power supply, setting wing nut aside.
Remove and discard power supply.
5.
Insert new power supply into place by wedging into open slot in housing and
screwing the wing nut back into place.
6.
Remake all wiring connections with wire nuts, using the guide below:
• Green power supply wire to fixture Ground (green) wire
• White power supply wire to fixture Neutral (white) wire
• Black power supply wire to fixture Hot (black) wire from the On-Off
switch
• Red power supply wire to red fixture wiring
• Blue power supply wire to blue fixture wiring
See Page 1 for:
• Installation Instructions using Line Connection
Date Issued: 12/11/15
FIG. 5
FIG. 6
FIG. 7
7.
Neatly tuck wires away in housing. Swing the
cover towards the fixture and close it by
pressing at the ends of the cover until the cover
snaps into place and is flush with the fixture.
CAUTION: Ensure that the wires are not pinched
or damaged by any part of the metal housing or
clips.
8.
Turn on power.
866-558-5706
We're here to help
Hrs: M-F 9am to 5pm EST
FIG. 8
IS-4ULED-CB_English
Page 2

Publicidad

loading

Este manual también es adecuado para:

4u k08 serie4u k12 serie4u k22 serie4u k30 serie