Enabling/Disabling Remote Control Wireless Transmission; Loop Out Setting; Remote Id Setting; Id Number Setting - NEC PlasmaSync 42XM5 Manual Del Usuario

Enabling/disabling remote control wireless
transmission
This function enables/disables remote control wireless
transmission.
Example: Setting "OFF"
On "IR REMOTE" of "OPTION3" menu, select "OFF", then
press the MENU/ENTER button.
OPTION 3
PREVIOUS PAGE
TIMER
PWR. ON MODE
CONTROL LOCK
IR REMOTE
LOOP OUT
REMOTE ID
ID NUMBER
VIDEO WALL
NEXT PAGE
SEL. ADJ.
Information
IR REMOTE settings
ON: Enables remote control wireless transmission.
OFF: Disables remote control wireless transmission.
Set "OFF" to avoid unwanted control from other remote
controls.

Loop Out setting

When this feature is set to ON, the received signal will be
looped out.
Example: Setting "ON"
On "LOOP OUT" of "OPTION3" menu, select "ON".
OPTION 3
PREVIOUS PAGE
TIMER
PWR. ON MODE
CONTROL LOCK
IR REMOTE
LOOP OUT
REMOTE ID
ID NUMBER
VIDEO WALL
NEXT PAGE
SEL. ADJ.
Information
LOOP OUT settings
ON: The received signal will be looped out via RGB1
terminal or VIDEO1 terminal.
OFF: The received signal will not loop out.
* Even if LOOP OUT is ON, signals won't be sent out if
POWER is being turned off.
To connect another display...
See page En-6.
If the RGB1 signal is present at the time the
power switched on...
The RGB1 input will be displayed regardless of the
setting of LOOP OUT.

REMOTE ID setting

Set the remote code to adapt the plasma monitor to the
remote control.
Example: Setting to "1"
On the "REMOTE ID" of "OPTION3" menu, select "1".
OPTION 3
PREVIOUS PAGE
TIMER
PWR. ON MODE
CONTROL LOCK
IR REMOTE
LOOP OUT
REMOTE ID
ID NUMBER
VIDEO WALL
NEXT PAGE
SEL. ADJ.
3 / 4
: OFF
: OFF
: OFF
: ALL
: ALL
EXIT RETURN
3 / 4
: OFF
: ON
: ON
: ALL
: ALL
EXIT RETURN
3 / 4
: OFF
: ON
: OFF
: 1
: ALL
EXIT RETURN
En-33
• Press and hold the POWER ON button, and release the
button when the indication saying that the code is set is
displayed. Or, press and hold the POWER STANDBY
button, and release the button when the power is turned
off.
Information
REMOTE ID setting
ALL: The remote code is not set.
1 to 4: The specified remote code is applied.

ID number setting

When using more than one of these displays, this function
sets ID numbers so that operation of the remote control
does not cause multiple monitors to operate at the same
time.
Example: Setting "2"
On "ID NUMBER" of "OPTION3" menu, select "2".
OPTION 3
PREVIOUS PAGE
TIMER
PWR. ON MODE
CONTROL LOCK
IR REMOTE
LOOP OUT
REMOTE ID
ID NUMBER
VIDEO WALL
NEXT PAGE
SEL. ADJ.
* To reset back to ALL
Press the CLEAR/SEAMLESS SW button.
Information
ID NUMBER settings
ALL: ID NUMBER will not be set.
1 to 256: ID NUMBER will be set.
When the ID NUMBER have been set
You can also set ID NUMBER for each remote control
to operate the plasma display individually. To do so,
see below.
To set the ID number for the remote control
Example: Setting "2"
Press the ID SELECT button on the remote control.
The "ID SELECT" screen appears.
On "ID NUMBER" of "ID SELECT" menu, select "2".
ID SELECT
POSITION : 1
ID NUMBER
ADJ.
* To reset back to ALL
Press the CLEAR/SEAMLESS SW button.
3 / 4
: OFF
: ON
: OFF
: ALL
: 2
RETURN
EXIT
: 2
RETURN
EXIT