Functional Description - Makita DML806 Manual De Instrucciones

2. Do not store the tool and battery cartridge in locations
where the temperature may reach or exceed 50°C
(122°F).
3. Do not give the tool a shock by dropping, striking, etc.
4. Do not expose the light to eyes continuously. It may
hurt them.
5. Do not cover or clog the lit tool with cloth or carton,
etc. Covering or clogging it may cause a flame.
6. Do not disassemble the charger or battery cartridge;
take it to a qualified serviceman when service or repair
is required. Incorrect reassembly may result in a risk
of electric shock or fire.
7. Use the tools only with specifically designated battery
packs. Use of any other battery packs may create a
risk of injury and fire.
8. If operating time has become excessively shorter, stop
operating immediately. It may result in a risk of
overheating, possible burns and even an explosion.
9. Do not use a damaged battery.
10. Charge the battery cartridge before completely
discharged. Always stop tool operation and charge the
battery cartridge when you notice less tool power.
11. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
12. If any problem develops, consult your nearest Makita
Service Center or dealer. To maintain product safety
and reliability, repairs, maintenance or adjustment
should be carried out by Makita Authorized Service
Center.
13. Charge the battery cartridge once in every six months
if you do not use it for a long period of time.
FCC Cautions to the user
The changes or modifications not expressly approved by
the party responsible for compliance could void the user's
authority to operate the equipment.
The equipment has been tested and found to comply with
the limits for a Class B Digital Device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction, may cause harmful
interference to radio communication.
However, there is no grantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
4
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
CAN ICES-005(B)/NMB-005(B)
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita lithium-ion batteries. Use of non-
genuine Makita batteries, or batteries that have been
altered, may result in the battery bursting causing fires,
personal injury and damage.

FUNCTIONAL DESCRIPTION

Installing or removing the battery
cartridge (Fig. 1)
CAUTION:
• Always switch off the tool before installing or removing
of the battery cartridge.
• Hold the tool and the battery cartridge firmly when
installing or removing battery cartridge. Failure to
hold the tool and the battery cartridge firmly may cause
them to slip off your hands and result in damage to the
tool and battery cartridge and a personal injury.
To remove the battery cartridge, slide it from the tool while
sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip it
into place. Insert it all the way until it locks in place with a
little click. If you can see the red indicator on the upper
side of the button, it is not locked completely.
CAUTION:
• Always install the battery cartridge fully until the red
indicator cannot be seen. If not, it may accidentally fall
out of the tool, causing injury to you or someone
around you.
• Do not install the battery cartridge forcibly. If the
cartridge does not slide in easily, it is not being inserted
correctly.
Use of non-genuine Makita batteries, or batteries that
have been altered, will void the Makita warranty for the
Makita tool and charger.
Switch operations (Fig. 2)
CAUTION:
• Do not look in the LED light or see the source of light
directly.