White Balance; Slow Response Of The Leds - IMG STAGELINE ODP-483RGBW Manual De Instrucciones

7 Additional Functions
GB
7.1 Key lock
A key lock may be activated as a protection
against unauthorized change of adjustments.
With activated lock, adjustments can only be
made after the input of a special key sequence.
1) Press the button MENU so many times until
the highest menu level is reached (in fig. 2 on
the very left).
2) Press the button UP or DOWN so many times
until the display shows
3) Press the button ENTER. The display shows
(key lock off).
4) Use the button UP or DOWN to switch to
The key lock is activated.
5) To make adjustments now, press the follow-
ing buttons successively:
If the display does not light up, press any but-
ton first, then
ENTER, UP, DOWN, UP, DOWN, ENTER.
Pressing the buttons UP and DOWN is
shown in each case by an asterisk ( ) on the
display. After finally pressing the button
ENTER, the display shows the last menu
item selected. As long as the display lights
up, adjustments can be made. If it extin-
guishes, the key lock is activated again.

7.2 White balance

For the colour white the spotlight has been fac-
tory-set so that the red, green and blue LEDs
light up at maximum brightness (
). However, for the colour white another
colour temperature may be adjusted (e. g. a
warm white or a cold white).
1) Press the button MENU so many times until
the highest menu level is reached (in fig. 2 on
the very left).
2) Press the button UP or DOWN so many times
until the display shows
3) Press the button ENTER. The display now
shows .
4) Press the button ENTER again. The display
now shows , or
000 and 255.
14
5) Use the button ENTER to select the three
6) Activate the adjusted colour temperature:
.
.
7) To be able to control the spotlight by DMX, go
© ©

7.3 Slow response of the LEDs

LEDs respond immediately to a change of the
brightness adjustment. To simulate the slow
response of standard lamps, the response can
be adjusted in 4 steps. For the 11-channel mode
channel 10 (chapter 6.3.5). For the 3-channel,
4-channel, 5-channel and 6-channel modes
. make the adjustment as follows:
1) Press the button MENU so many times until
and a number between 2) Press the button UP or DOWN so many times
All rights reserved by MONACOR
manual may be reproduced in any form or by any means for any commercial use.
= brightness of the red LEDs
= brightness of the green LEDs
= brightness of the blue LEDs
adjusting functions successively and the but-
ton UP or DOWN to adjust the brightness in
each case so that the desired colour temper-
ature will result.
a) Press the button MENU so many times
until the display shows
b) Press the button DOWN twice so that the
display shows .
c) Press the button ENTER. The display
shows the indication ,
or .
d) If is not shown, press the button UP
or DOWN as many times as necessary.
e) Press the button ENTER. If the display
shows , the adjusted colour tempera-
ture is activated, if it shows
with the button UP or DOWN.
from the menu branch to the menu item
:
a) Press the button MENU so many times
until the display shows
b) Press the button UP or DOWN so many
times until the display shows
c) Press the button ENTER. The display
shortly shows the DMX start address. If
DMX control signals are received now, a
point must flash on the display.
this adjustment is made via the DMX
the highest menu level is reached (in fig. 2 on
the very left).
until the display shows .
3) Press the button ENTER. The display shows
the indication
.
4) If is not shown, press the button UP or
DOWN as many times as necessary.
5) Press the button ENTER. The display shows
the present adjustment:
immediate response
slightly slow response
...
again.
response as slow as possible
Select the desired adjustment with the button
UP or DOWN.
6) To be able to control the spotlight by DMX, go
, ,
from the menu branch
:
a) Press the button MENU so many times
until the display shows
b) Press the button UP or DOWN so many
times until the display shows
, switch to
c) Press the button ENTER. The display
shortly shows the DMX start address. If
DMX control signals are received now, a
point flashes on the display.
again.
8 Specifications
.
Data protocol: . . . . . . . . . DMX 512
Number of
DMX channels: . . . . . . . . selectable:
Light source . . . . . . . . . . 48 LEDs
Power per LED . . . . . . 3 W
Beam angle . . . . . . . . 25°
Power supply: . . . . . . . . . 230 V~ / 50 Hz
Power consumption: . . . . max. 170 VA
Protective class
of housing: . . . . . . . . . . . IP 67
Dimensions: . . . . . . . . . . ∅ 240 mm × 230 mm
Weight: . . . . . . . . . . . . . . 8.5 kg
Subject to technical modifications.
® INTERNATIONAL GmbH & Co. KG. No part of this instruction
, , , or
to the menu item
again.
.
3, 4, 5, 6 or 11
12 red, 12 green,
12 blue, 12 white