Napa Carlyle Tools 6-1137 Manual De Instrucciones página 5

OPERATION
The air regulator knob can be used
as an air throttle, if there are no
other means of regulating air. Turn
the air regulator knob all the way
to highest position for maximum
power.
The air regulator can be used to
adjust torque to the ap prox i mate
tightness of a known fastener. When
tight en ing nuts not requiring critical
torque values, run nut up flush and
then tighten an additional one­
quarter to one­half turn (slight ad di­
tion al turning is necessary if gaskets
are being clamped). For additional
power needed on dis as sem bly
work, turn regulator to its fully open
position. This im pact wrench is rated
at 1" USS bolt size. Rating must
be down graded for spring U bolts,
tie bolts, long cap screws, double
depth nuts, badly rusted conditions
and spring fas ten ers, as they absorb
much of the impact power. When
possible, clamp or wedge the bolt to
prevent springback.
WARRANTY
For a complete list of authorized air tool repair centers please visit www.toolwarrantyrepair.com.
I m port ant : DO NO T RET U R N
P R O D U C T T O
PU RC HAS E.
WA RRANTY PO LI CY:
P r o f e ssi o na l A i r T o o l is w a r r a n t e d
a g a i n s t d e f e c t s i n m a t e r i a l a n d
wo r k ma n sh ip f o r a p e r i o d o f O n e
(1 ) Y ea r f ro m t h e d a t e o f o r ig i ­
nal p u rc h as e. W e w i ll r e p a ir o r
r ep l a c e , a t o u r o p t io n, a n y p a r t
wh i ch p ro ve s to b e d e f e c t iv e in
ma t e r ia l or w o rkm a n shi p . R e p a ir s
or r e p l a c e m e nt s ar e w a r r a n t e d a s
d e s cri b ed a b o ve f o r t h e d u r a t io n
o f t h e o r i g i n a l w a r r a n t y p e r i o d .
Th i s w a rra n ty d o e s no t a p p l y t o
p r od u c t s w h ic h ha ve b e e n s u b ­
j e c t e d t o a b u s e , m i s u s e , m o d i ­
f i c a t i o n , n e g l e c t , l a c k o f m a i n ­
PLEASE REVIEW ALL WARNING INSTRUCTIONS PRIOR TO OPERATION. SAVE THIS MAN U AL FOR FUTURE REF ER ENCE.
6-1137
Soak rusted nuts in pen e trat ing oil
and break rust seal before removing
with im pact wrench. If nut does
not start to move in three to five
sec onds, use a larger size impact
wrench. Do not use impact wrench
be yond rated ca pac i ty, as this will
dras ti cal ly reduce tool life.
The forward/reverse lever is used
to change the direction of the tool.
When the lever is moved to the
right, the tool is in a forward or right
hand direction. When the lever is
moved to the left, the direction is
reverse or left hand.
NOTE: Actual torque on a fastener
is directly related to joint hardness,
tool speed, condition of socket
and the time the tool is allowed to
impact.
Use the simplest possible tool-to-
socket hook up. Every connection
absorbs energy and reduces power
t e n a n c e , u s e i n a p r o d u c t i o n ­
P L A C E O F
r e l a t e d s e r v i c e , o r r e p a i r e d b y
a n y o n e o th er th an an Au t h or iz ed
M a s t e r
T h i s N A P A
A i r
F o r c o m pl e te l i s ti n g of Au th o ri ze d
M a s t e r
e n c l o s e d
R e p a ir F or m , o r v is it www. to ol­
w a r r a n ty r e pai r . co m
W AR R A NTY C LA I M P RO CE DU RE
I f y o u r N A P A P r o fe ss io n al Air Too l
p r o v e s de fec ti v e w i th i n it s or ig in a l
O n e ( 1 ) Y e ar w ar r a n ty per io d, it
m u s t b e r e tu r n e d to a n Au th or i ze d
M a s t e r
T o o l S e r v i ce C e n ter .
i s r e s p o n s i b l e f o r s h i p p i n g t h e
N A P A P r o f e s s i o n a l
T o o l S e r v i c e C e n t e r .
R e p a i r C e n t e r s ,
C u s t o m e r W a r r a n t y
N A P A P r o f e s s i o n a l
C u s tom er
5
Specifications
Drive Size ........................................ 1"
Standard Bolt Size ................... 1­5/8"
Max. Free Speed .............. 4,000 RPM
Torque Range ..........650­1,600 ft./lbs.
Max. Torque .................... 1,600 ft./lbs.
Air Inlet ................................1/2" NPT
Min. Hose Size ..................... 1/2" I.D.
Avg. Air Cons. .......................12 CFM
Recom. Air
Pressure ... 90­115 PSIG (6.2­8.0 bar)
Length ........................................... 22"
Weight. ................................25.74 lbs.
Sound Level ........................ 98.8 dBA
Forward/Reverse
Lever
too l Fr ei gh t P re­ Pai d alo n g wit h
Pro of o f P u rch a s e a n d com plet e d
C u s to mer Wa rr an t y R epa ir F o r m.
s e e
A i r
Air Inlet
Rev. 05/14/19