Cameo STUDIO PAR 64 LED CAN Manual De Usuario página 16

OPERATION / BEDIENUNG / UTILISATION / OPERACIÓN / OBSŁUGA / UTILIZZO
EN NOTE
When the projector is properly connected to the mains, the following information appears successively in the display during the startup process:
"Software Update, Please Wait..." (for service purposes only), the software version "Software V1.xx" and "WELCOME TO cameo". After this operation,
the projector is ready for use and changes to the mode that was previously selected.
STATIC COLOUR
This mode offers the ability to separately adjust the intensity for each of the 6 LED groups and to generate an unlimited number of different colours
(colour mixing).
Press the MODE button until "STATIC" appears in the upper line of the display. By repeatedly pressing the ENTER button, select the LED group for
which you want to change the brightness level (please note the cursor in the display, Rxx = red, Gxx = green, Bxx = blue, Wxx = white, Axx = amber,
UVxx = UV / black light). Now you can set the intensity of the selected light from 00 to 99 using the UP and DOWN buttons (example: R00 = red at
0%, i.e. out. R99 = red at 100%, i.e. maximum brightness).
Adjust the flash frequency of the strobe effect by pressing ENTER repeatedly until the cursor shows "Fxx". Now you can activate the strobe effect
using the UP and DOWN buttons and set the flash frequency from 00 to 99 (F00 = strobe effect deactivated, F01 = approx. 1 Hz, F99 = approx. 20
Hz). Confirm with ENTER.
RED
Intensity R00 - R99
GREEN
Intensity G00 - G99
COLOUR MACROS
In this mode, one of the 6 basic colours of the projector or one of the 9 different mixed colours can be selected as a preset.
Press the MODE button repeatedly until "MACRO" appears in the upper line of the display. Now press ENTER and then select one of the 15 colour
presets using the UP and DOWN buttons. Confirm with ENTER.
MACRO 01 = red
MACRO 02 = green
MACRO 03 = blue
MACRO 04 = white
MACRO 05 = amber
MACRO 06 = UV / black light
MACRO 07 = yellow
MACRO 08 = cyan
COLOUR CHANGE
In the colour change mode (Jumping Mode), 12 different colours alternate in rapid succession (red, green, blue, white, amber, yellow, cyan, lavender,
pink, light green, magenta, turquoise, orange). The speed of the program is adjustable separately and a stroboscope effect can also be activated.
Press the MODE button until „JUMPING" appears in the upper line of the display. Now, press ENTER until the cursor appears in the lower line of the
display, and then select the rate (SPEED) using the UP and DOWN buttons, with the colours alternating from 00 to 99.
Confirm with ENTER. The indicator in the bottom line of the display changes to „FLASH:xx". At the same time, the cursor will appear in the bottom
line and you can activate the stroboscope effect using the UP and DOWN buttons and adjust the flash frequency from 00 to 99 (FLASH:00 = strobe
deactivated, FLASH: 01 = approx. 1 Hz, FLASH: 99 = approx. 20 Hz). Confirm with ENTER.
COLOUR CHANGE
Rate SPEED:00 - SPEED:99
16
BLUE
Intensity B00-B99
WHITE
Intensity W00 - W99
MACRO 09 = lavender
MACRO 10 = light green
MACRO 11 = magenta
MACRO 12 = turquoise
MACRO 13 = orange
MACRO 14 = cool white
MACRO 15 = warm white
STROBOSCOPE
Flash frequency FLASH:00 - FLASH:99
AMBER
Intensity A00 - A99
UV / BLACK LIGHT
Intensity UV00 - UV99
STROBOSCOPE
Speed F00 - F99