Canon ImageRUNNER ADVANCE 45551i Manual Del Usuario página 44

Appendix
radioélectriques (RF) CNR-102 de l'IC. Cet
équipement doit être installé et utilisé en
gardant une distance de 20 cm ou plus entre le
radiateur et le corps humain.
Regulatory information for users in Mexico
Módulo WLAN instalado adentro de este
producto
IFETEL RCPCAFM15-0072
CANON INC.
FM1M944
La operación de este equipo está sujeta a las
siguientes dos condiciones:
(1) es posible que este equipo o dispositivo no
cause interferencia perjudicial y
(2) este equipo o dispositivo debe aceptar
cualquier interferencia, incluyendo la que
pueda causar su operación no deseada.
Regulatory information for users in Argentina
Incluye módulo Wireless LAN Module Marca Canon
Inc., Modelo FM1M944, CNC C-14229
Regulatory information for users in Uruguay
4551i/4545i/4535i/4525i contains URSEC approved
Wireless LAN Module (Model name: FM1M944).
Information Security Standard (IEEE 2600)
This machine is compliant with IEEE Std 2600™
- 2008 (hereinafter referred to as IEEE 2600), a
global information security standard for
multifunction peripherals and printers, and is able
to achieve the security requirements defined in
IEEE 2600.*
For information on how this machine meets the
security requirements defined in IEEE 2600, see
User's Guide > Managing the Machine > IEEE 2600
* IEEE 2600.2 CC Authentication has not been
obtained for this machine by itself.
Disclaimers
The information in this document is subject to
change without notice.
CANON INC. MAKES NO WARRANTY OF ANY KIND
WITH REGARD TO THIS MATERIAL, EITHER EXPRESS
OR IMPLIED, EXCEPT AS PROVIDED HEREIN,
INCLUDING WITHOUT LIMITATION, THEREOF,
WARRANTIES AS TO MARKETABILITY,
MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE OF USE, OR NON-INFRINGEMENT. CANON
INC. SHALL NOT BE LIABLE FOR ANY DIRECT,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF
ANY NATURE, OR LOSSES OR EXPENSES RESULTING
FROM THE USE OF THIS MATERIAL.
The following applies in California, USA only:
The battery included with your product contains
Perchlorate Material and may require special
handling.
See http://www.dtsc.ca.gov/hazardouswaste/
perchlorate/ for details.
Users in the U.S.A.
Preinstallation Requirements for Canon Facsimile
Equipment
[NOTE]
The fax function is available only if the FAX Board
is installed.
A. Location
Supply a suitable table, cabinet, or desk for the
machine.
See "Specifications" in the User's Guide for
specific dimensions and weight.
44
B. Order Information
1. A single telephone line (touch-tone or rotary)
should be used. If the Super G3 2nd Line Fax
Board is installed, a multi telephone line
(touch-tone or rotary) can be used.
2. Order an RJ11-C telephone wall jack (USOC),
which should be installed by the telephone
company. If the RJ11-C wall jack is not present,
telephone/facsimile operation is not possible.
3. Order a normal business line from your
telephone company's business representative.
The line should be a regular voice grade line
or an equivalent one. Use one line per unit. If
the Super G3 2nd Line Fax Board is installed,
you can use a multi-line.
DDD (Direct Distance Dial) line
-or-
IDDD (International Direct Distance Dial) line if
you communicate overseas
[NOTE]
Canon recommends an individual line following
industry standards, i.e., 2500 (touch-tone) or 500
(rotary/pulse dial) telephones. A dedicated
extension off a PBX (Private Branch eXchange)
unit without "Call Waiting" can be used with your
facsimile unit. Key telephone systems are not
recommended because they send nonstandard
signals to individual telephones for ringing and
special codes, which may cause a facsimile error.
C. Power Requirements
The machine should be connected to a standard
120 volt AC, three-wire grounded outlet only.
Do not connect this machine to an outlet or
power line shared with other appliances that
cause "electrical noise." Air conditioners, electric
typewriters, copiers, and machines of this sort
generate electrical noise that often interferes
with communications equipment and the
sending and receiving of documents.
Connection of the Equipment
This equipment complies with Part 68 of the FCC
rules and the requirements adopted by the
ACTA. On the rear panel of this equipment is a
label that contains, among other information, a
product identifier in the format
US:AAAEQ##TXXXX. If requested, this number
must be provided to the telephone company.
The REN is used to determine the number of
devices that may be connected to a telephone
line. Excessive RENs on a telephone line may
result in the devices not ringing in response to
an incoming call. In most, but not all areas, the
sum of RENs should not exceed five (5.0). To be
certain of the number of devices that may be
connected to a line, as determined by the total
RENs, contact the local telephone company. For
products approved after July 23, 2001, the REN
for this product is part of the product identifier
that has the format US:AAAEQ##TXXXX. The
digits represented by ## are the REN without a
decimal point (e.g., 03 is a REN of 0.3).
An FCC compliant telephone line cable and
modular plug is provided with this equipment.
This equipment is designed to be connected to
the telephone network or premise wiring using a
compatible modular jack that is Part 68
compliant.
This equipment may not be used on coin service
provided by the telephone company.
Connection to party lines is subjected to state
tariffs.
In Case of Equipment Malfunction
Should any malfunction occur which cannot be
corrected by the procedures described in the
User's Guide, disconnect the equipment from
the telephone line cable and disconnect the
power cord. The telephone line cable should not
be reconnected or the main power switch
turned ON until the problem is completely
resolved. Users should contact their local
authorized Canon Facsimile Service Dealer for
the servicing of equipment.
If your equipment malfunctions, please contact
your local authorized Canon dealer from whom
you purchased the equipment (if under
warranty), or with whom you have a servicing
contract. If you are not sure who to contact, and
have both purchased and are using the
equipment in the U.S.A., please refer to the
"SUPPORT" page on Canon U.S.A.'s Web site
(http://www.usa.canon.com).
Rights of the Telephone Company
If this equipment imageRUNNER ADVANCE
4551i/4545i/4535i/4525i causes harm to the
telephone network, the telephone company
may temporarily disconnect service.
The telephone company also retains the right to
make changes in facilities and services that may
affect the operation of this equipment. When
such changes are necessary, the telephone
company is required to give adequate prior
notice to the user. However, if advance notice is
not possible, the telephone company will notify
the customer as soon as possible. Also, the
customer will be advised of his/her right to file a
complaint with the FCC if he/she believes it is
necessary.
WARNING
The Telephone Consumer Protection Act of 1991
makes it unlawful for any person to use a
computer or other electronic device, including
FAX machines, to send any message unless such
message clearly contains in a margin at the top
or bottom of each transmitted page or on the
first page of the transmission, the date and time
it is sent and an identification of the business or
other entity, or other individual sending the
message and the telephone number of the
sending machine or such business, other entity,
or individual. (The telephone number provided
may not be a 900 number or any other number
for which charges exceed local or long distance
transmission charges.)
[NOTE]
In order to program this information into your
machine, you should complete the procedure
for registering your name, unit's telephone
number, time, and date as described in Setting
Up or Basic Operations in the User's Guide.
Users in Canada
Preinstallation Requirements for Canon Facsimile
Equipment
[NOTE]
The fax function is available only if the FAX Board
is installed.
A. Location
Supply a suitable table, cabinet, or desk for the
machine.
See "Specifications" in the User's Guide for
specific dimensions and weight.
B. Order Information
1. A single telephone line (touch-tone or rotary)
should be used. If the Super G3 2nd Line Fax
Board is installed, a multi telephone line
(touch-tone or rotary) can be used.
2. Order a CA11A modular jack which should be
installed by the telephone company. If the
CA11A jack is not present, installation cannot
occur.
3. Order a normal business line from your
telephone company's business representative.
The line should be a regular voice grade line
or an equivalent one. Use one line per unit. If
the Super G3 2nd Line Fax Board is installed,
you can use a multi-line.