Campbell Hausfeld CHN70700 Manual De Instrucciones Y Lista De Piezas página 6

Operating Instructions and Parts Manual
Important Safety Information (Continued)
e. Always work in a well-ventilated area. Wear OSHA-
approved dust mask.
Always disconnect the tool from the power
source when unattended, performing any
maintenance or repair, clearing a jam, loading, unloading , or
moving the tool to a new location.
Always fit tool with a fitting or hose coupling
on or near the tool in such a manner that all
compressed air in the tool is discharged at the time the fitting or
hose coupling is disconnected. Do not use a check valve or any other
fitting which allows air to remain in the nailer. Death or serious
personal injury could occur.
Never carry the nailer by the air hose or pull
the hose to move the nailer or a compressor.
Keep hoses away from heat, oil and sharp edges. Replace any hose
that is damaged, weak or worn. Personal injury or tool damage
could occur.
Do not drive a nail on top of other nails. The
nail could glance and cause death or a serious
puncture wound.
Do not use tool if laser guide power switch does
not turn it on or off. Any tool that cannot be
controlled with the switch is dangerous and must be repaired.
f. Ensure the laser guide power switch is in the off position
before inserting batteries. Inserting the batteries into the
tool with the switch on invites accidents.
g. Turn laser guide Off before making any adjustments,
changing accessories, or storing. Such preventive safety
measures reduce the risk of accidents.
When batteries are not in use, keep them away
from metal objects such as paper clips, coins,
keys, nails, or screws that can make a connection from one terminal
to another. Shorting the battery terminals together may cause sparks,
burns, a fire, or damage to the batteries.
h. This tool must NOT be modified or used for any
application other than that for which it was designed.
i. Under abusive conditions, liquid may be ejected from the
batteries. Avoid contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes, seek medical help.
Liquid ejected from the batteries may cause irritation or
burns.
Use of controls or adjustments or performance
of procedures other than those specified herein
may result in hazardous radiation exposure.
j. The use of optical instruments with this product will
increase eye hazard.
k. Turn off laser beam when it is not in use or when tool will
be left unattended.
l. Do not remove any labels from the tool.
6
www.chpower.com
m. The product will emit a laser beam from the aperture.
The users of the product shall be limited to professional
operators. In normal operation and maintenance
conditions, the operators shall wear protective eyewear to
prevent injury to the eyes.
Do not expose tool to extreme heat.
n. Do not store in locations where the temperature may
reach or exceed 120°F (49°C), such as a metal tool shed, or
a car in the summer. This can lead to deterioration of the
battery.
o. Do not disassemble tool.
p. Remove batteries when storing tool for an extended time.
NOTE: Battery temperature will increase during and shortly
after use.
Only use new Alkaline replacement batteries [two (2) AAA
required]. Do not mix old and new batteries.
Battery shelf life - the included batteries may be in a slightly
depleted state or dead depending on how long the product has
awaited purchase. Do not return product to store for depleted
batteries; please call Campbell Hausfeld at 1-800-543-6400 for
assistance.
q. Do not modify or alter the nailer or any nailer parts. Do
not use the nailer if any shields or guards are removed or
altered. Do not use the nailer as a hammer. Personal injury
or tool damage may occur.
Do not use any type of flammable gases or
oxygen as a power source for the nailer.
Use filtered, lubricated, regulated compressed air only. Use of a
compressed gas instead of compressed air may cause the nailer to
explode which will cause death or serious personal injury.
Never use gasoline or other flammable liquids
to clean the nailer. Never use the nailer in
the presence of flammable liquids or gases. Vapors could ignite by a
spark and cause an explosion which will result in death or serious
personal injury.
r. Avoid using the nailer when the magazine is empty.
Accelerated wear on the nailer may occur.
Do not modify or disable the Work Contact
Element (WCE). Do not tie or tape the WCE
or trigger in a depressed position. Death or serious personal injury
could result.
Always check that the Work Contact Element
(WCE) is operating properly. A nail could
accidentally be driven if the WCE is not working properly. Personal
injury may occur.
Do not touch the trigger unless driving nails.
Never attach air line to nailer or carry nailer
while touching the trigger. The tool could eject a fastener which will
result in death or serious personal injury.
CHN70700