Regulatory Compliance Approvals - HME VDB103 Instrucciones De Instalación

REGULATORY COMPLIANCE APPROVALS

HME is committed to compliance with the laws and regulations of each country where HME markets the product below.
Applicant Name : HM Electronics, Inc.
Applicant Address : 2848 Whiptail Loop, Carlsbad, CA 92010 USA
Manufacturer Name : HM Electronics, Inc.
Manufacturer Address : 2848 Whiptail Loop, Carlsbad, CA 92010 USA
Country of Origin : USA
Product Name : Vehicle Detection Board
Product Regulatory Model Number : RFM100
This document was prepared in the English language. In case this document is translated into another language and a discrepancy arises between languages,
the English version shall prevail as being the version which best expresses the intent of the parties. Any notice or communication given in conjunction with this
document must include an English version.
Caution: All products are compliant with regulatory requirements detailed in this document when the user follows all the installation instructions and
operating conditions per HME specifications.
Caution: Product modifications not expressly approved by the party responsible for compliance can void the user's authority to operate the equipment.
Cause: Use of accessories and peripherals other than those recommended by HME may void the product's compliance as well as the user's authority to
operate the equipment.
Caution: Operating or storing the product outside the specified temperature range of 0-50º Celsius can damage it.
RF Exposure Notice
This module transmitter complies with radiation exposure limits set forth for the general public (uncontrolled environment) per FCC, IC and EC rules and
guidelines. This module transmitter must be installed to operate with a minimum separation distance of 7.87 inches (20 cm) from all persons. To avoid the
possibility of exceeding radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm.
Avis d'exposition RF
Ce module émetteur est conforme aux limites d'exposition aux radiations énoncées pour le grand public (environnement incontrôlé) selon les règles et directives
FCC, IC et EC. Ce module émetteur doit être installé de façon à fonctionner avec une distance de séparation minimale de 20 cm (7,87 pouces) de toutes
personnes. Pour éviter la possibilité de dépasser les limites d'exposition aux fréquences radio, la proximité humaine de l'antenne ne doit pas dépasser 20 cm.
US Compliance Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Model RFM100 is a module transmitter that is installed inside a host or finished product. It was certified with single modular approval per Federal Communications
Commission (FCC) CFR47 Telecommunications, Part 15.212 under Subpart C Intentional Radiators. Single modular approval does not necessarily eliminate FCC
testing on the finished product. For example, FCC Part 15 B requirement for the digital device (unintentional radiator) of a composite system, RF Exposure and/or
Co-location requirement may still be applicable to the finished product.
The host integrator is responsible to ensure that the finished product complies with all applicable FCC equipment authorization regulations.
The FCC certification of the module transmitter is voided if the host integrator does not follow its FCC's grant notes and operation condition/installation instructions.
This module transmitter contains an integrated antenna, which is also integral to its FCC certification, so using any other antenna would void its FCC certification.
This module transmitter must not collocate or operate simultaneously with any other antenna or transmitter within a host device, except in accordance with FCC
multi-transmitter procedures.
If the FCC ID of this module transmitter is not visible when the module transmitter is installed inside a host or finished product, then the exterior surface of the host
or finished product must also display a label with the following or similar wording: "Contains FCC ID: BYMRFM100".
European Union (CE mark)
Hereby, HME declares that the Vehicle Detector Board (Regulatory Model RFM100) is in compliance with the following directives and standards:
Directives:
Radio Equipment Directive 2014/53/EU
RoHS Directive 2011/65/EU
Standards:
EN 300 328
EN 300 330
EN 301 489
Brand : HME
7