Utilisation / Funcionamiento - Echo EGi-4000 Manual Del Operador

OPERATION
WARNING
Do not allow familiarity with this product to make you
careless. Remember that a careless fraction of a second
is sufficient to inflict serious injury.
WARNING
Do not use any attachments or accessories not recom-
mended by the manufacturer of this product. The use
of attachments or accessories not recommended can
result in serious personal injury.
NOTICE
This product is equipped with a spark arrestor that has
been evaluated by the USDA Forest Service; however,
product users must comply with Federal, State, and lo-
cal fire prevention regulations. Check with appropriate
authorities. Contact customer service or an authorized
dealer to purchase a replacement spark arrestor.
NOTICE
Before each use, inspect the entire product for dam-
aged, missing, or loose parts,such as screws, nuts, bolts,
caps, etc. Tighten securely all fasteners and caps and
do not operate this product until all missing or damaged
parts are replaced. Please contact customer service or
an authorized dealer for assistance.
Applications
This generator is designed to supply electrical power for
operating compatible electrical lighting, appliances, tools,
and motor loads.
Before Operating the Unit
 Only use OUTSIDE and at least 20 feet (6 m) away from
windows, doors, and vents as recommended by the U.S.
Department of Health and Human Services Centers for
Disease Control and Prevention. Your specific home and/
or wind conditions may require additional distance.
 NEVER use inside a home or garage, EVEN IF doors and
windows are open.
 Always position the generator on a flat firm surface.
Special Requirements:
There may be General or State Occupational Safety and
Health Administration (OSHA) regulations, local codes or
ordinances that apply to the intended use of the generator.
Please consult a qualified electrician, electrical inspector, or
the local agency having jurisdiction:
 In some areas, generators are required to be registered
with local utility companies.
 If the generator is used at a construction site, there may
be additional regulations which must be observed.
14
ECHO COMMAND
See Figure 7.
NOTE: The LCD display will not work unless the unit is running.
Fuel level: The fuel level indicator will show how much fuel
is remaining.
Load level: The load level indicator will show the connected
load. If the generator is approaching the maximum wattage/
amperage capacity, the indicator will blink. If load level ca-
pacity is exceeded, the LCD display will show OVERLOAD.
To reset the generator, remove all loads from the generator
and press the reset button (see fig. 1). Add loads back to
the generator one at a time being careful not to exceed the
generators wattage rating.
Run time: The LCD display will show the approximate re-
maining run time based on fuel level and load.
Auto idle: The LCD display will show if the idle is on or off.
Bluetooth : Once paired, the LCD display will indicate
®
whether or not the ECHO COMMAND
through Bluetooth .
®
Checking/Adding Lubricant
See Figure 8.
Attempting to start the engine before it has been prop-
erly filled with lubricant will result in equipment failure.
NOTE: If a separate engine manual is provided for this
product, please follow the instructions provided in the
engine manual instead of the information listed below.
Engine lubricant has a major influence on engine perfor-
mance and service life. For general, all-temperature use,
SAE 10W-30 is recommended. Always use a 4-stroke motor
lubricant that meets or exceeds the requirements for API
service classification SJ.
This engine comes with a feature that will shut off the engine
when a specific lubricant level is not maintained. The engine
will not restart until an appropriate lubricant level is reached.
NOTE: Non-detergent or 2-stroke engine lubricants will
damage the engine and should not be used.
 Unscrew the oil cap/dipstick and remove.
 Wipe dipstick clean and re-seat in hole; do not re-thread.
 Remove dipstick again and check lubricant level. Lubricant
level should fall between the minimum and maximum
marks on the dipstick.
 If level is low, add engine lubricant until the fluid level
rises between the minimum and maximum marks on the
dipstick.
 Replace and secure the oil cap/dipstick.
English
LCD Display
™
app is connected
™
NOTICE