Publicidad
Idiomas disponibles
Idiomas disponibles
Manuale del d'uso ed installazione – Cleaner5 12V
( GB )
WIRING
It is necessary to connect the plug with a socket provided with earth, making sure that the tension corresponds to
that indicated on the back of the machine.
WATER FEEDING
This machine does not need any linking to the water grid; it is fitted up with a boiler, which must be filled up
manually. In order to fill up the machine with the water it is necessary to unscrew (in counterclockwise way) the
security valve (1), then fill up the boiler using the supplied funnel.
Pour the fluid to reach the maximum capacity (it is possible to pour warm water into the boiler to make the heating
of the fluid easier).
It is possible to check the level of the water through the special glass (8). At the end of this operation screw the
safety valve and make sure to have not poured any fluid on the machine.
WORKING OF THE MACHINE
A) Press the general switch (7). The pilot of the switch lights up and at the same time the heating of the fluid starts.
The pilot (14) showing the working of the element lights up.
It is necessary to wait for a heating time of about 12 minutes (when the fluid is cold). When the heating pilot (14)
lights up the machine is in the conditions to start working.
It is possible to check the internal pression of the boiler using the manometer (5). B) Press the special push-button
(6) to predisose the working of the gun; the lamp showing the level glass will light up (8).
The steam comes out simply by pressing the button set upon the gun. It is possible to regulate the steam quantity by
using the knob (3).
OPERATIONS TO EXECUTE AT THE END OF THE WORK
In order to turn the machine off it is necessary to disconnect the general switch (7) and the gun connection switch
(6). It is advisable to loosen the security valve (1) to avoid that the machine remains in pression without any reason
(but remember to screw the plug again when you want to reutilize the machine).
IMPORTANT
Never open the security valve (1) and the drain cock (11) when the boiler is in pression.
In order to execute the topping-up of the water it is necessary to switch the machine off and loosen the security
valve (1) slightly, in oder to let the steam go out. Let the steam go out using the iron; when the manometer (5)
shows about 1 bar, slightly loosen the valve (1) until the pression is exhausted. In this way the operator will run no
risks. Never leave the machine feeded; in this case switch both the boiler and the gun off.
MAINTENANCE AND CONTROL
- Security valve (1): check periodically that the small hole on the side is free from fur, because it must allow the
discharge of the steam in case of anomalous working of the machine.
- Steam tubes and wirings: check the condition of the electric and pneumatic plans periodically, replacing the
damaged components if necessary.
- Boiler: periodically discharge the water inside the boiler in order to eliminate the calcareuos deposits; to execute
this operation properly it is advisable to switch the machine off with the inside fluid cold (with the manometer (5)
showing zero), to avoid burns.
Open the drain cock (11) to clear possible deposits away. At the end of this operation close the drain cock carefully.
Don't utilize the machiner for other use, from those for that has been realized
Alwais wear DPI in the respect of the disposition antiaccident.
Don't approach to machine with inflammable materials.
Never leave the boiler, with lighted and placed on covering's cloth.
The use is allow only to autorized person and howener adults.
Proibition to clean or verificate during the movement.
Prohibition to use water for putting the fire on elettric equipement under
tension.
Don't put on the machine material with dimension ad weight such as to compromise the
stability's machine.
Don't licht the machine in presence of more people that caused accidental
contact, could compromise the safety condition on ironing machine.
Don't put in function the device when the cable is not perfectly entre or the
structure is damage.
del 05-07-2016 - Cleaner5 12V - R01
Pagina 4 di 16
Publicidad
