Publicidad
Idiomas disponibles
Idiomas disponibles
ADDITIONAL SAFETY INSTrUCTIONS
Connect the device only to a power point with a resi-
dual current protective device (RCD) with a measured
residual current of not more than 30 mA.
• Keep the mains cable and extension cable away from
the grinding disk and saw chain. In the event that it is
damaged or severed, immediately disconnect
the plug from the socket.
Do not touch the cable before it has been disconnec-
ted from the mains.
Risk of electric shock.
• The replacement of the plug and cable must always
be carried out by the manufacturer of the electric tool
or his/ her customer service in order to avoid
any hazards.
• Only switch the device on once it is safely fixed to
the worktop.
• For your own safety only use accessories and atta-
chments which were stated in the operating instruc-
tions or recommended or specified by the tool
manufacturer.
• Only use grinding tools recommended by the manu-
facturer. Do not use any saw blades. Ensure that the
dimensions match those of the device.
• Only use grinding discs where the printed rotational
speed is at least as high as what has been specified on
the name plate of the device.
• Carry out a visual inspection of the grinding disc befo-
re use. Do not use any damaged or deformed grinding
discs. Replace any damaged or worn grinding discs.
• Never operate the device without spark protection or
protective hoods.
Periodically readjust the spark protection in order to
offset the wear and tear of the grinding disc (distance
max. 2 mm).
• Replace the grinding disc if the spark protection and
the workpiece support can no longer be readjusted to
a distance of max. 2 mm at the latest.
• Make sure that the sparks produced by grinding do
not present a danger, e.g. reach people or ignite flam-
mable substances.
• Always wear safety goggles, safety gloves, respira-
tory protection and ear protection when grinding, bru-
shing and separating.
• Never keep the fingers between the grinding disc and
spark protection or in close proximity to the protective
hoods.
There is a risk of crushing.
• The rotating parts of the device cannot be covered
due to functional reasons.
Therefore, proceed cautiously and hold the workpiece
firmly in order to avoid slipping which could cause your
hands to come into contact with the grinding
belt or grinding disc.
• The workpiece gets hot during grinding. Do not touch
the machined area, allow it to cool down. There is a
risk of burn ing. Do not use coolants or the like.
• If you are tired or have consumed alcohol or tablets,
do not work with the device. Always have a break on
time.
• Switch the device off and remove the mains plug
- to loosen a blocked insertion tool,
- if the connection line is damaged or entangled,
- in case of unusual sounds.
Residual risks
Even if properly operating and handling this electric
tool, some residual risks will remain. Due to its con-
struction and build, this electric tool may present the
following
hazards:
a) Lung damage, if suitable respiratory protection is
not worn.
b) Hearing damage, if suitable ear protection is not
worn.
c) Damages to health due to - touching the area of the
grinding tool which was not covered;
- the ejection of pieces from workpiece or damaged
grinding discs.
d) Damage to your health caused by swinging your
hands and arms when operating the appliance for lon-
ger periods of time or if the unit is not held or
maintained properly.
Warning! During operation, this electric tool genera-
tes an electromagnetic field which, under certain cir-
cumstances, may impair the functionality of active or
passive medical implants. To reduce the risk
of serious or lethal injuries, we recommend that per-
sons with medical implants consult their doctor and the
manufacturer of their medical implant before operating
the machine.
- Use protective equipment against noise,
dust and vibrations !!!
KEEP THESE SAFETY INSTRUCTIONS FOR
FUTURE REFERENCE !!!
DESCrIPTION (A)
The bench grinder with belt sander is a combined
device equipped with a grinding disc and an adjustable
grinding belt. The device is provided with a spark
protection and protective hoods for the protection of
the user.
For the function of the operating parts, please refer to
the descriptions below.
1 Spark protection (two-piece)
2 Adjusting screw for spark protection
3 Protective hood grinding disc
4 Engine housing
5 Star grip nut to install the workpiece support grinding
belt
6 Workpiece support grinding belt
7 Clamping lever grinding belt
8 Clamping screw for upper belt idler
9 Protective hood grinding belt
10 Grinding belt
11 Fixing screws for grinding disc cover
12 Grinding disc cover
13 Bore holes for table mounting
14 On/off switch
14a On switch
14b Off switch
15 Fixing screws for grinding disc
51
Publicidad
