FALMEC Mizar Manual De Instrucciones página 17

USE OF MECHANICAL PUSH BUTTON CONTROL PANEL
Light button
Press this button to turn the hood light on (button pressed in) or off
(button out)
OFF button
OFF
Press this button to switch the motor off
USE OF ELECTRONIC PUSH BUTTON CONTROL PANEL
Timer/Filters alarm
Pressing the key with the motor active at any speed activates the Timer
function: this function determines the auto switch-off of the hood
after 15 minutes of operation. Activation of the function is signalled
by a RED flashing light.
With the Timer function active, the hood can still be switched off by
the user at any time by pressing the key
matically disabled and the RED light will turn off. Should the speed be
changed with the Timer function active, the latter will be automatically
disabled.
On the other hand, ignition of the fixed RED light indicates a grease
filter alarm: this alarm notifies that it is time to wash the metal an-
ti-grease filters (the alarm is triggered after approximately 30 hours of
use). After cleaning the filters, disable the alarm and reset the counters
by keeping the key pressed for 3 seconds.
To disassemble and assemble the anti-grease metal filters, re-
fer to the instructions on drawing
LIGHTING
The range hood is equipped with high efficiency, low consumption LED spotlights with extremely long duration under normal use con-
ditions.
Should the LED spotlight need to be replaced, proceed as shown in the figure
MAINTENANCE
Before cleaning or carrying out maintenance operations, disconnect the equipment by removing the plug or switching off the main switch.
Regular maintenance guarantees proper operation and good performance over time.
Special attention is to be paid to the metal anti-grease filters and active carbon filters. In fact, frequent cleaning of the filters and their supports ensures that
no grease is accumulated on the hood, which is dangerous and can cause fires.
EXTERNAL CLEANING
You are advised to clean the external surfaces of the hood at least once every 15 days to prevent oily substances and grease from sticking to them.
To clean the brushed stainless steel hood, the Manufacturer recommends using "Magic Steel" wipes. Alternatively, it can be cleaned using a damp cloth, slightly mois-
tened with neutral, liquid detergent or denatured alcohol. Finish off cleaning by rinsing well and drying with soft cloths.
Do not use too much water next to the push button control panel and lighting devices in order to prevent humidity from reaching electronic
parts. You must not use detergents containing abrasive, acid or corrosive substances or abrasive cloths: a direct consequence of not complying
with these warnings will result in irreversible deterioration of the hood's surface.
The Manufacturer declines all responsibility for failure to comply with these instructions.
OFF 1
1
2
3
: the function will be auto-
G
on page 6.
17
2 3
Button 1: Press this button (button in) to start or set the motor at min-
imum speed
Button 2: Press this button (button in) to start or set the motor at me-
dium speed
Button 3: Press this button (button in) to start or set the motor at max-
imum speed
Mode button (ON/OFF)
Pressing the key switches on (or off ) the hood motor: it starts at the
previously selected speed prior to switching it off (desired speed func-
tion). Should you wish to use a different speed, set if by using the +
and - keys.
Button +
By pressing the key, the motor speed increases. Speeds 1, 2 and 3 are
displayed by the number of LEDs switched on, excluding the light and
timer LEDs.
The + key in the version with 4 speeds has an intermittent light: the
4th speed or intensity is timed and after approximately 7 minutes the
motor automatically switches to 3rd speed.
Button -
By pressing the key, the motor speed reduces. Speeds 1, 2 and 3 are
displayed by the number of LEDs switched on, excluding the light and
timer LEDs.
Light button
ON: light on (lit button) OFF: light off
I
on page 6.
600
m /h
3
800
m /h
3