Safety; Specifications - jbc Premium RMSE-A Manual Del Usuario

Safety

It is imperative to follow safety guidelines to prevent electric
shock, injury, fire or explosion.
- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.
- The power cord must be plugged into approved bases. Be sure that it is properly grounded
before use. When unplugging it, hold the plug, not the wire.
- Do not work on electrically live parts.
- The tool should be placed in the stand when not in use in order to activate the sleep mode.
The soldering tip, the metal part of the tool and the stand may still be hot even when the station is
turned off. Handle with care, including when adjusting the stand position.
- Do not leave the appliance unattended when it is on.
- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.
- Use a "non residue" classified flux and avoid contact with skin or eyes to prevent irritation.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protective glasses and gloves when
working to avoid personal harm.
- Utmost care must be taken with liquid tin waste which can cause burns.
- This appliance can be used by children over the age of eight and also persons with reduced
physical, sensory or mental capabilities or lack of experience provided that they have been given
adequate supervision or instruction concerning use of the appliance and understand the hazards
involved. Children must not play with the appliance.
- Maintenance must not be carried out by children unless supervised.
32

Specifications

Complete Rework station with Electric Pump
RMSE-1A / RMSE-2A / RMSE-9A
- Total weight: 16.6 kg (36.6 lb)
- Ambient Operating Temperature: 10 to 40ºC (50-104ºF)
JTE-1C 120V 50/60Hz. Input fuse 8A
JTE-2C 230V 50/60Hz. Input fuse 4A
JTE-9C 100V 50/60Hz. Input fuse 8A
- Weight: 2.3 Kg (5.07lb)
- Dimensions: 148 x 184 x 140
- Nominal Power: 700W
- Temperature range: Room temperature / 150ºC to 450°C (300ºF to 840ºF)
Cool mode: T Off. Used to blow air at room temperature.
- Idle Temp. Stability (still air): ± 20 ºC (± 36 ºF)
- Air flow regulation: 10-50 SLPM
- Vacuum: 30% / 228 mmHg / 9 inHg
- USB interface station-PC
- P-005 Pedal connection
DDE-1A 120V 50/60Hz. Input fuse: 4A. Output: 23.5V
DDE-2A 230V 50/60Hz. Input fuse: 2A. Output: 23.5V
DDE-9A 100V 50/60Hz. Input fuse: 5A. Output: 23.5V
- Weight: 4.3 Kg (9.3 lb)
- Dimensions: 148 x 120 x 232 mm
- Output Peak Power: 150W per tool
- Temperature Range: 90-450°C (190-840 ºF)
- Idle Temp. Stability (still air) ±1.5 ºC (±3 ºF)
- Tip to ground resistance: <2 ohms
- Tip to ground voltage: <2mV RMS
- USB-A / USB-B / Peripherals connectors
- RJ12 connector for Robot
MSE-A
- Weight: 1.2 Kg (2.6 lb)
- Dimensions: 145 x 55 x 225 mm
- Vacuum: 75% / 570 mmHg / 22.4 inHg
- Flow rate: 9 SLPM
- P-005 Pedal connection
Complies with CE standards
ESD protected housing "skin effect"
w w w.jbctools.com
33