Before Using The Equipment - EINHELL HEROCCO 36 Manual De Instrucciones

The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with Power-
X chargers.
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L sound pressure level ........................ 92 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ........................ 103 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Impact drilling in concrete
Vibration emission value a
K uncertainty = 1.5 m/s
Chiseling
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Anl_Herocco_36_28_SPK9.indb 18 Anl_Herocco_36_28_SPK9.indb 18
= 10.2 m/s
2
h
2
= 14.0 m/s
2
h
2
- 18 -
GB
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
prolonged period or is not properly guided
and maintained.
Limit the operating time.
All stages of the operating cycle must be
considered (for example, times in which the
electric tools are switched off and times in which
the tool is switched on but operates without load).

5. Before using the equipment

Be sure to read the following information before
you put the cordless impact drill into operation:
1. Charge the battery pack only with a charger
from the Power-X-Change series.
2. Only ever use sharp drill bits and screwdriver
bits which are suitable for the purpose and in
faultless condition.
3. Using a cable/pipe detector, check the area
you want to work on for concealed electric
cables and gas and water pipes.
5.1 Additional handle (Fig. 2/Item 6)
For safety reasons you must only use the im-
pact drill with the additional handle.
The additional handle (6) enables you to achieve
better stability whilst using the impact drill. For
safety reasons the machine must not be used wit-
hout the additional handle (6).
The additional handle (6) is secured to the impact
drill by a clamp. Turning the handle anti-clockwise
(viewed from the handle) will release the clamp.
Turning the handle clockwise tightens the clamp.
Release the clamp of the additional handle fi rst.
Then you can swivel the additional handle (6)
into the most comfortable working position for
yourself. Now turn the additional handle (6) in the
opposite direction again until the additional hand-
le (6) is secure.
06.07.2020 13:51:49 06.07.2020 13:51:49