3M Speedglas 100 Manual Del Usuario

3
Speedglas 100 – Welding Helmet and Hardhat Adapter for
™
use with 3M XLR8 Hardhat, and Other Alternate Hardhat
™
Configurations
** Refer to 3M™ Speedglas™ 100 Welding Helmet, 3M™ XLR8 Hardhat, or Listed Alternate Hardhat
Complete User's Instructions for List of Product Warnings and Proper Use
Ensemble masque pour soudeurs et adaptateur de casque
dur 100 Speedglas à utiliser avec le casque dur XLR8 3M
™
et d'autres configurations de casque dur
** Consulter les directives d'utilisation complètes du masque pour soudeurs 100 Speedglas™, du
casque dur XLR8 3M™ et des autres casques durs indiqués pour connaître les mises en garde et les
directives d'utilisation adéquates du produit.
Speedglas 100 – Careta para soldadura y Adaptador de
™
casco para uso con Casco 3M
alternativas de Casco
**Remítase a las Instrucciones de Careta para soldadura 3M™ Speedglas™ 100, Casco 3M™ XLR8 o
Casco alternativo listado para consultar la lista de advertencias y uso adecuado del producto.
3M Occupational Health and
Environmental Safety Division
3M Center, Building 0235-02-W-70
St. Paul, MN 55144-1000
Printed in U.S.A.
3M and Speedglas are trademarks of the 3M Company.
V-Gard is a registered trademark of Mine Safety Appliances Co. – MSA.
© 2010 3M Company. All rights reserved.
3M Occupational Health
and Environmental Safety Division
3M Canada Company
P.O. Box 5757 London, Ontario N6A 4T1
Printed in U.S.A.
3M and Speedglas are trademarks of the 3M Company, used under license in Canada.
V-Gard is a registered trademark of Mine Safety Appliances Co. – MSA.
© 2010 3M Company. All rights reserved.
Division des produits d'hygiène
industrielle et de sécurité
environnementale de 3M
Compagnie 3M Canada
C.P. 5757
London (Ontario) N6A 4T1
Imprimé au Canada.
3M et Speedglas sont des marques de commerce de 3M, utilisées sous licence au Canada.
V-Gard est une marque déposée de Mine Safety Appliances Co. – MSA.
© 3M, 2010. Tous droits réservés.
3M México S.A. de C.V.
Av. Santa Fe No. 190
Col. Santa Fe, Del. Álvaro Obregón
México D.F. 01210
Impreso en EUA.
3M y Speedglas son marcas registradas de 3M Company.
V-Gard es una marca registrada de Mine Safety Appliances Co. – MSA.
© 2010 3M Company. Todos los derechos reservados.
XLR8 y otras configuraciones
™
98-XXXX-XXXX-X/1
34-8704-7238-7
• This is an addendum to the User Instructions for the 3M™ Speedglas™ 100 Auto-Darkening
Welding Helmets. Always read and follow the User Instructions provided with each individual
component of any welding helmet or hard hat assembly. User Instructions include important
warnings and use limitations. Failure to do so may result in sickness or death.
• Do not use any welding product without appropriate training. For proper use, see supervisor
or User Instructions or call 3M in U.S.A.1-800-243-4630. In Canada, call 1-800-267-4414.
Failure to do so may result in sickness or death.
• Always wear ANSI Z87.1-2003 compliant safety spectacles in addition to any welding
helmet. Failure to do so may result in permanent eye injury and vision loss. In Canada,
™
follow CSA Z94.3 and/or the requirements of the authority having jurisdiction in your region.
Introduction
Two ANSI standards cover performance requirements for welding shields combined with hard
hats: Z87.1-2003 Eye and Face Protection Devices and Z89.1-2003 Industrial Head Protection.
Both standards require welding helmets and hard hats to be tested as a complete assembly, as
they would be worn by a welder. Assembling a welding hard hat using components from different
manufacturers or brands voids ANSI compliance unless tests verify that the assemblies remain
compliant with the ANSI requirements.
These User Instructions cover the 3M™ Speedglas™ 100 welding helmet models listed in Table 1,
mounted to certain hard hats that have been independently tested for compliance with the above
referenced ANSI standards. In all cases, the 3M™ Speedglas™ 100 Hardhat Adapter for 3M™
Speedglas™ 100 helmets (part number 07-0014-00NR) was used as the mounting device.
IMPORTANT: To maintain ANSI compliance, use only the exact components listed in these User
Instructions.
Specifications
− Eye and Face Impact: ANSI Z87.1-2003 high impact protector (Z87+)
− Head Impact: ANSI Z89.1-2003, Type I (top impact). Refer to hard hat literature for electrical
rating.
Table 1. 3M™ Speedglas™ Welding Helmet Options
Speedglas™ Helmet Model
07-0012-10BL
07-0012-11BL
07-0012-31BL
07-0012-31XX
Hard Hat Options
The configurations that were tested and passed the above referenced ANSI impact test
requirements are summarized in Table 2. Use with hardhats other than those listed in Table 2 have
not been tested as complete assemblies and would void compliance with the above reference
ANSI standards. These User Instructions do not cover 3M™ Speedglas™ ProTop or other 3M™
Speedglas™ systems sold complete with hard hats.
Manufacturer Hard Hat Model
3M XLR8 with 6 Point Ratchet
MSA V-Gard® w/Fas-trac Suspension
Assembly Instructions
1. Follow Figs. 1-4, to properly remove and replace the 3M™ Speedglas™ 100 headgear with the 3M™
Speedglas™ 100 Hardhat Adapter (part number 07-0014-00NR) as shown in Figs. 1 and 2.
2. Assure to re-configure the head suspension in the hardhat to face the brim backwards as is shown in
Fig. 3.
3. Attach the 3M™ Speedglas™ 100 assembly to the hardhat as shown in Fig. 4 and adjust the Hardhat
Adapter "pin lock" for a tight fit around the hardhat for a completed assembly.
FOR MORE INFORMATION
In United States, contact:
Website: www.3M.com/OccSafety
Technical Assistance: 1-800-243-4630
For other 3M products:
1-800-3M-HELPS or
1-651-737-6501
WARNING
Description
100, ADF 100, Shade 10, Black
100, ADF 100, Shade 11, Black
100, ADF 100V, Shades 8-12, Black
100, ADF 100V, Shades 8-12 with Graphics
Table 2. Hard Hat Options
Hard Hat Part No.
45995-00001
475358 thru 475365 & 488146
Fig. 1
Fig. 2
Fig. 3
Fig. 4