Nevir NVR-459U Manual De Instrucciones página 9

IMPORTANT - MP3 FILE NAME FORMAT
PLEASE TAKE CARE TO USE ONLY REGULAR ENGLISH ALPHABETS
(A TO Z) & NUMERALS (0 TO 9) IN THE FILE NAMES OF MP3 SONGS.
CHARACTERS SUCH AS " _ " (UNDERSCORE) & "
RESULT IN THE FILES BEING UNREADABLE OR INCONSISTENTLY
UNRECOGNIZABLE BY THE PLAYER.
ALTHOUGH THIS PRODUCT IS FULLY COMPATIBLY WITH USB 1.1 & 2.0 STANDARDS,
A SMALL PERCENTAGE (ABOUT 5%) OF USB FLASH DRIVES MIGHT NOT BE
READABLE, DUE TO THOSE USB-FLASH DRIVE MANUFACTURERS
NON-COMPLIANCE WITH THE FULL (OFFICIAL) USB 1.1 / 2.0 STANDARDS.
IMPORTANT
REMOVAL OF USB DRIVES
NEVER REMOVE (OR UNPLUG) USB-DRIVES FROM THE SET DURING
PLAYBACK OF MP3 SONGS FROM THESE MEDIA. ALWAYS PRESS
STOP FIRST AND THEN PRESS AND HOLD (FOR 2 SECONDS)
THE "PLAY/ PAUSE/ USB" KEY TO SWITCH TO "CD" MODE BEFORE
REMOVING OR UNPLUGGING USB MEMORY, TO PREVENT DAMAGE
TO YOUR SONG FILES OR MEMORY DEVICES.
IMPORTANT: THIS UNIT DOES NOT SUPPORT USB-MP3 PLAYER,
DUE TO THEIR INHERENT LACK OF SOFTWARE COMPATIBILITY.
ONLY USB "PEN DRIVES" (FLASH MEMORY USB DRIVES) CAN BE USED,
FOR MP3 PLAYBACK.
IMPORTANT POINT
Please do NOT use a USB Extension Cable to connect your
USB FLASH DRIVE to the USB PORT of this unit.
Such cables can pick up additional interference which can corrupt
the data flow, preventing normal operation and usage of the USB port.
Always connect your USB Flash Drive DIRECTLY to the USB PORT
without any USB extension cables.
REPEAT PLAYBACK FUNCTION
- AT ANYTIME DURING PLAYBACK, PRESS THE "REPEAT" KEY
AS FOLLOWS:
PRESS ONCE, DISPLAY SHOWS A FLASHING "REPEAT" SYMBOL:
= TO REPEAT THE CURRENT TRACK
PRESS TWICE, DISPLAY SHOWS A "REPEAT" SYMBOL REMIND ON:
= TO REPEAT ALL TRACK (FULL CD)
" (SPACE) MAY
NOTE :
REPEAT
REPEAT
E-7
PROGRAMMING THE CD-PLAYER
- THE CD PLAYER CAN BE PROGRAMMED TO PLAY ANY SEQUENCE OF UPTO 20
TRACKS FOR AUDIO-CD / 99 TRACKS FOR CD-MP3 / USB-MP3, AS DESIRED.
- ALWAYS PRESS THE STOP KEY BEFORE STARTING THE PROGRAMMING.
- PRESS THE PROGRAM KEY, THE DISPLAY WILL SHOW A
P0 1
AND THE DISPLAY WILL SHOW "
"MEMORY PROGRAMMING MODE", AT MEMORY POSITION NO. 1.
- PRESS THE "NEXT" OR "BACK" KEY TO SELECT THE TRACK (SONG)
NUMBER YOU WISH TO BE STORED IN THE FIRST MEMORY (PROGRAM) POSITION,
AND PRESS THE PROGRAM KEY TO CONFIRM YOUR SELECTION.
- WHEN YOU PRESS PROGRAM KEY THE DISPLAY WILL ADVANCE TO THE NEXT
P02
MEMORY POSITION NUMBER (EG. "
- REPEAT THE PREVIOUS 2 STEPS, EACH TIME SELECTING ANY TRACK NUMBER OF
YOUR CHOICE TO BE STORED IN THE SUCCESSIVE MEMORY (PROGRAM)
POSITIONS.
- AFTER EACH TRACK NUMBER, REMEMBER TO PRESS THE PROGRAM KEY.
- AFTER A MAXIMUM OF SONGS (OR LESS) HAVE BEEN SELECTED AS DESCRIBED
ABOVE, PRESS THE PROGRAM KEY.
- ALSO, THE P SYMBOL WILL REMAIN "ON" TO INDICATE THAT YOU HAVE SAVED A
PROGRAM-MEMORY (SEQUENCE).
- PRESSING PLAY WILL NOW PLAY BACK THE "SAVED SEQUENCE" IN THE
PROGRAM MEMORY.
- PRESSING NEXT/ BLACK WILL MOVE TO THE NEXT OR PREVIOUS SONG IN THE
SAVED SEQUENCE.
- TO CLEAR (CANCEL) THE ENTIRE PROGRAM WHICH IS STORED IN THE MEMORY,
SIMPLY PRESS "STOP" TWICE (
THE SET.
USING THE AUDIO LINE IN CONNECTION (AUX-INPUT)
- YOU CAN CONNECT THE AUDIO OUTPUT OF AN EXTERNAL DEVICE SUCH AS A
CD-PLAYER TO THIS UNIT, TO LISTEN TO THE SOUND OF THAT DEVICE
THROUGH THE AMPLIFIER OF THIS MUSIC SYSTEM.
- TO CONNECT AN EXTERNAL AUDIO DEVICE (eg. MP3 PLAYER, PLEASE USE A
STANDARD (NOT INCLUDED) STEREO CABLE (WITH 3.5MM TO 3.5MM PLUGS) TO
CONNECT THE "HEADPHONE-OUT OR AUDIO LINE-OUT" OF THE EXTERNAL
DEVICE TO THE AUX-INPUT SOCKET OF THIS UNIT.
- SWITCH THE FUNCTION SWITCH TO " CD/MP3/USB/AUX ".
- SWITCH ON THE EXTERNAL DEVICE (eg. CD-PLAYER).
- START PLAYBACK OF THE EXTERNAL DEVICE AND ADJUST THE VOLUME
CONTROL OF THE MAIN UNIT TO THE DESIRED LEVEL.
- REMEMBER TO SWITCH OFF THE POWER OF THE MUSIC SYSTEM (MAIN UNIT)
WHEN YOU ARE FINISHED USING THE EXTERNAL DEVICE.
SYMBOL (FLASH)
P
" , TO INDICATE THAT THE SET IS NOW IN
" FOR 2ND POSITION).
SYMBOL DISAPPEAR) , OR SWITCH "OFF"
P
E-8