Auto Channel Scan; Language Selection - Emerson SLC195EM8 2 El Manual Del Propietario

I
NITIAL SETTING
BACK LIGHT
You can set the desired brightness mode.
(Refer to "Back Light Setting" on page 22.)
COLOR TEMP.
You can adjust color temperature ("NORMAL", "WARM",
"COOL").
(Refer to "Color Temperature" on page 22.)
DTVCC
In addition to the basic closed caption described
on page 18, DTV has its own closed caption called
DTVCC.
(Refer to "DTV Closed Caption" on page 20.)
PC SETTING
You can adjust the position, stability and clarity of the
PC screen.
This menu will appear only in PC mode, and can only
be set when the unit detects the PC input signal.
(Refer to "PC Settings" on page 26.)

Auto Channel Scan

If you switch wires (e.g., between antenna and CATV) or if you move the
unit to a diff erent area after the initial setting, or if you restore the DTV
channel you deleted, you will need to perform auto channel scan.
Before you begin:
Make sure if the unit is connected to antenna or cable.
1
Press [SETUP] to display the main menu.
2
Use [Cursor K / L] to select "CHANNEL SETUP",
then press [ENTER].
or
3
Use [Cursor K / L] to select your desired preset type,
then press [ENTER].
or
• When aerial antenna is connected,
select "AUTO PRESET CH(TV)", "AUTO PRESET CH(DTV)"
or "AUTO PRESET CH(TV/DTV)".
• When connected to CATV, select
"AUTO PRESET CH (CATV)".
12
EN
e.g.) digital TV mode
- TV SETUP -
PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION [OFF]
BACK LIGHT [BRIGHT]
COLOR TEMP. [NORMAL]
DTVCC
e.g.) digital TV mode
- CHANNEL SETUP -
ADD/DELETE(DTV)
AUTO PRESET CH(DTV)
AUTO PRESET CH(TV/DTV)
AUTO PRESET CH(CATV)
! CATV takes approx. 50min.
• Scanning and memorizing the channels automatically
start.
• When the scanning and memorizing are completed,
the lowest memorized channel will be displayed.
• When you selected "AUTO PRESET CH(TV/DTV)", the
lowest memorized analog channel will be displayed
when the scanning and memorizing are completed.
If there is no analog channel, the lowest memorized
digital channel will be displayed.
Note:
• If you connect the cable system directly, contact the CATV
installer.
• If you press [POWER] or [SETUP] during auto channel scan,
the setting will be canceled.
• When no channel can be received by auto channel scan,
"NO TV SIGNALS" will be displayed on the TV screen.
• Channel settings will be saved even if the power fails.
• If you have Spanish or French menus and need English,
press [SETUP]. Use [Cursor K / L] to select "IDIOMA"
or "LANGAGE". Press [ENTER] to select "ENGLISH". Press
[SETUP] to remove the main menu.
• With regard only to the digital channel, even after the
scanning is complete if you unplug the AC power cord
before turning off the unit by pressing [POWER], the
channel setting may be lost.

Language Selection

You can choose English, Spanish, or French as your on-screen language.
1
Press [SETUP] to display the main menu.
2
Use [Cursor K / L] to select "LANGUAGE",
then press [ENTER] repeatedly to change the setting.
or
3
Press [SETUP] to exit.
e.g.) digital TV mode
D25
AUTO PRESET CH(DTV)
e.g.) digital TV mode
- TV SETUP -
PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION [OFF]
BACK LIGHT [BRIGHT]
COLOR TEMP. [NORMAL]
DTVCC
ENGLISH
ESPAÑOL
FRANÇAIS