Virutex FR1192T Manual De Instrucciones página 9

9.1 APPLICATION FOR RADIUSES (Fig. 5)
Attach the square to the head in the inverted po-
sition, using pivot I as the centre of the circumfe-
rence. Adjust the required length of the radius and
hold in place using the knobs on the head J.
9.2 HINGE TEMPLATE APPLICATION (Fig. 6)
To make the recesses for hinges using the FR1192T
trimmer, first attach the guide ring 12.50.002 using
screws K, then attach HSS bit 11.30.059 or HM bit
11.40.059, with a 7.6 mm diameter.
For rounded hinges, use a bit that is the same width
as the hinge and a guide ring with inner diameter A
2 mm greater than the bit. (See guide rings).
9.3 APPLICATION FOR COPYING
ON ANY TEMPLATE (Fig. 8)
Attach the most appropriate guide for the bit to be
used to the head with the screws K.
(See guide rings).
10. MAINTENANCE OF BRUSHES
AND COLLECTOR (Figs. 9 and 10)
Remove the screws L (Fig. 9) that hold the side co-
vers N and detach them from each other.
Remove the brush-holder P (Fig. 10) with small
screwdriver O, using one of the brush-holder side
tabs to lever it out. Push back the end of spring
Q. Keep it in this position to extract the brush and
replace it with a new genuine Virutex brush. Re-in-
sert the brush-holder, ensuring that it is firmly po-
sitioned in the casing and that each of the brushes
exerts a small amount of pressure on the collector.
Re-attach the covers N with the corresponding
screws, making sure that no wires get caught in the
process.
It is advisable to leave the machine running for 15
minutes once the brushes have been changed.
If the collector burns or juts out, it should be servi-
ced by a VIRUTEX service technician.
Always keep the lead and plug in good working
condition.
11. ACCESORIES
Template guide ring (Fig. 15)
Code For bits
12.50.001 6 mm
12.50.002 8 ó 7,6
12.50.003 10 mm
12.50.004 12 mm
Ø A ØB
8 mm 10
10 12
12 14
14 16
12.50.025 14 mm
12.50.035 16 mm
12.50.040 Sliding shoe (Fig.11)
12.50.041 Flat sliding shoe (Fig.12)
18.50.042 45° sliding shoe (Fig.13)
12.22.024 Chuck Ø 8mm
12.22.085 Chuck Ø 1/4"
12.22.084 Chuck collet Ø 6 mm
Always use bits with the correct size
of shank for the chuck being used and
adjust the velocity of the tool.
Hinge fitting attachment 17.50.000 for fitting hinges
without using a template (Fig. 14)
12. RECOMMENDATIONS
Switch off the machine before handling it. Keep the
cable and socket in good condition. Use the trimming
heads and accessories appropiates and corresponding
to the trimming machine you have. They do not fit
on other models.
13. NOISE LEVEL AND VIBRATIONS
The noise and vibration levels of this device have
been measured in accordance with European stan-
dard EN 60745-2-17 and EN 60745-1 and serve as
a basis for comparison with other machines with
similar applications.
The indicated vibration level has been determined
for the device's main applications and may be used
as an initial value for evaluating the risk presented
by exposure to vibrations. However, vibrations may
reach levels that are quite different from the declared
value under other application conditions, with other
tools or with insufficient maintenance of the electrical
device or its accessories, reaching a much higher
value as a result of the work cycle or the manner in
which the electrical device is used.
Therefore, it is necessary to establish safety measures
to protect the user from the effects of vibrations,
such as maintaining both the device and its tools
in perfect condition and organising the duration
of work cycles (such as operating times when the
machine is subjected to loads, and operating times
when working with no-load, in effect, not in use, as
reducing the latter may have a considerable effect
upon the overall exposure value).
14. WARRANTY
16 18
18 20
9