General Notes On Safety; Use Of The Machine For Purposes For Which It Is Intended; Incorrect Use; Ec Declaration Of Conformity - SUHNER ABRASIVE UWK 10-R125 Documentación Técnica

1. N
1.1 g
enerAl notes on sAfety
This technical document is applicable for the machine
UWK 10-R125. The machine may only be handled by per-
sonnel who are qualified.
Hold power tools by insulated gripping surfaces when
performing an operation where the cutting tool may con-
tact hidden wiring or its own cord. Contact with a «live»
wire will make exposed metal parts of the tool «live» and
shock the operator.
WARNING Read all safety warnings and all in-
structions. Failure to follow the warnings and in-
structions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
1.2 u
se of the mAchine for purposes for
which it is intended
The machines are intended for the purpose of cutting,
roughing and brushing of metal and stone materials with-
out the use of water.
1.3 i
ncorrect use
All uses other than those described under section
1.2 are regarded as incorrect use and are there-
fore not admissible.
1.4 ec
declArAtion of conformity
Translations of the «EG-Koformitätserklärung (Original)».
Otto Suhner GmbH of Trottäcker 50, D-79713 Bad Säck-
ingen, hereby declares under sole responsibility that the
product with the serial or batch no. (see reverse side) com-
plies with the requirements under the Directive 2014/30/
EU, 2006/42/EC, 2011/65/EU. Applied standards: EN ISO
12100, EN 60745, EN 55014-1, EN 55014-2, EN 61000-
3-2, EN 61000-3-3. Document Agent: T. Fischer. D-Bad
Säckingen, 10/2019.
T. Fischer/Division manager
2. C
2.1 p
rior to tAking the mAchine into service
Before connecting tool to a power
source, be sure the voltage sup-
plied is the same as specified on
the name plate of the tool. The power sup-
ply should not vary more than 10% above or below the
voltage indicated on the nameplate. Check grinding tool
prior to use. The grinding tool must be mounted centrally
and positioned against the limit stop. The maximum al-
lowable speed of the tool and of the chuck may not be
24
S
oTES oN aFETy
ommISSIoNINg
exceeded under any circumstances. Observe national
regulations. Fit hand protection.
2.2 t
Aking the mAchine into service
Preselect speed with adjusting wheel according to speed
table.
Level 1: 4200min
-1
Level 2: 5200min
-1
Level 3: 6400min
-1
During operation never exceed the speed which
has been matched to the grinding tool specifica-
tions!
2.2.1 t /t
urn on urn off
The switch must be in the OFF position. To turn the ma-
chine on, push the ON/OFF switch toward the front until it
clicks in. Press the ON/OFF swith to trigger the blocking
and the machine shuts down.
2.3 r
Ating dAtA
Power voltage
Power Input 230/240V
Power Output 230/240V
Power Input 120V
Power Output 120V
No-load speed
Max. tool Ø
Grinding spindle thread
Sound pressure level EN 60745
Noise emission level
Vibration EN 60745
Weight w/o cable
Protection class
Level 4: 7600min
-1
Level 5: 8800min
-1
Level 6: 10000min
-1
120/230/240V, 50/60Hz
1530W
1000W
1340W
800W
10500min
-1
125mm
M14 / ø19
89dB(A), K=3dB
100dB(A), K=3dB
5.2m/s , K=1.5m/s
2 2
2.6kg
II