Bosch PSB 550 RE Manual Original página 11

OBJ_BUCH-1752-004.book Page 11 Tuesday, August 2, 2016 12:59 PM
Intended Use
The machine is intended for impact drilling in brick, concrete
and stone as well as for drilling in wood, metal and plastic. Ma-
chines with electronic control and right/left rotation are also
suitable for screwdriving.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Depth stop*
2 Front sleeve
3 Rear sleeve
4 Keyless chuck
5 Button for depth stop adjustment *
6 "Drilling/Impact Drilling" selector switch
7 Lock-on button for On/Off switch
8 Rotational direction switch
9 On/Off switch
10 Auxiliary handle (insulated gripping surface) *
11 Wing bolt for adjustment of auxiliary handle *
12 Handle (insulated gripping surface)
13 Universal bit holder*
14 Screwdriver bit*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Impact Drill PSB 550 RE
PSB 5500 RE
Article number 3 603 A27 0.. 3 603 A27 0..
Rated power input W
Output power W
-1
No-load speed min
-1
Impact rate min
Rated torque Nm
Torque at max. output
power Nm
Right/left rotation
Spindle collar dia. mm
Max. drilling dia.
– Concrete mm
– Steel mm
– Wood mm
Chuck clamping range mm
Weight according to
EPTA-Procedure
01:2014 kg
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Bosch Power Tools
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-1.
Typically the A-weighted noise levels of the product are:
Sound pressure level 97 dB(A); Sound power level
108 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
determined according to EN60745-2-1:
Drilling into metal: a
Impact drilling into concrete: a
Screwdriving without impact: a
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
PSB 570 RE terns.
PSB 5700 RE
PSB 6000 RE
Assembly
 Before any work on the machine itself, pull the mains
550 570
260 260
Auxiliary Handle (see figure A)
50 – 3000 50 – 3000
 Operate your machine only with the auxiliary handle
33000 33000
1.1 1.1
 Before any work, make sure that the wing bolt 11 is
7.5 7.5
 
The auxiliary handle 10 can be set to any position for a secure
43 43
and low-fatigue working posture.
Turn the wing bolt for adjustment of the auxiliary handle 11 in
10 10
anticlockwise direction and set the auxiliary handle 10 to the
8 8
required position. Then tighten the wing bolt 11 again in
25 25
clockwise direction.
2 – 13 2 – 13
Adjusting the Drilling Depth (see figure A)
The required drilling depth X can be set with the depth stop 1.
Press the button for the depth stop adjustment 5 and insert
1.6 1.6
the depth stop into the auxiliary handle 10.
/II /II
The knurled surface of the depth stop 1 must face downward.
Pull out the depth stop until the distance between the tip of
the drill bit and the tip of the depth stop corresponds with the
desired drilling depth X.
(triax vector sum) and uncertainty K
h
2
=4.0 m/s , K=1.5 m/s
h
=33 m/s
h
<2.5 m/s
h
plug.
10.
firmly tightened. Loss of control can cause personal inju-
ry.
English | 11
2
2 2
, K=3.5 m/s
2 2
, K=1.5 m/s
1 609 92A 1N6 | (2.8.16)