Before Starting The Equipment - Toolson PRO-RF 521 Manual De Instrucciones

Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
•
The machine must be set up so that it stands
firmly, i.e. it must be securely screwed to a
work bench, the base frame supplied in deli-
very, or similar.
•
All covers and safety devices must be cor-
rectly attached before the machine is used for
the first time.
•
The cutting wheel must rotate smoothly.
Assembly (Fig. 1-6)
•
Fasten the feet (18) to the base frame (12)
with the 4 screws (19).
•
Turn the sub-frame upright.
•
Insert the two screws (37) for the trough fix-
ture through the square holes and place the
trough (3) in the base frame (12).
Anl_PRO_RF_521_SPK7.indb 18 Anl_PRO_RF_521_SPK7.indb 18
GB
•
Fasten the cooling water pump (13) to the
mount (38). Place the tile cutter into the
trough and screw on the trough fixture (39).
•
Unscrew and remove the star handle screw
(11) and spacer (40) and keep them in a safe
place.
•
Fill the trough with water until the cooling wa-
ter pump (13) is completely immersed.
Notice!
To guarantee proper operation, the cooling water
hose (14) must not be kinked during installation.
Danger!
It must be impossible for the cable and the coo-
ling water hose to get into the cutting area.
6. Operation
6.1 ON/OFF switch (Fig. 7)
•
To switch on, press the "I" on the ON/OFF
switch (16).
•
Before you begin cutting, wait until the cutting
wheel has reached maximum speed and the
cooling water pump (13) has started supply-
ing the cutting wheel with water.
•
To switch off, press the "0" on the switch (16).
6.2 90° Cutting (Fig. 8/9)
•
Loosen the star grip screw (27).
•
Set the angle stop (5) to 90° and retighten the
star grip screw (27).
•
Retighten the screws (28) to fasten the angle
stop (5).
•
Move the machine head (29) to the far end
with the handle (9).
•
Position the tile against the rail fence (6) on
the angle stop (5).
•
Switch on the tile cutting machine.
•
Notice! Always wait until the cooling water
has reached the cutting wheel (2) first.
•
Move the machine head (29) slowly and
smoothly forward through the tile with the
handle (9).
•
Switch off the tile cutting machine after com-
pletion of cutting.
6.3 45° Diagonal cut (Fig. 10)
•
Set the angle stop (5) to 45°.
•
Cut as described in 6.2.
- 18 -
23.04.15 11:17 23.04.15 11:17