Publicidad
Idiomas disponibles
Idiomas disponibles
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (off for
0.3 seconds). In such a case, fi rst let the battery cool,
then start charging.
○ When the charge indicator lamp fl ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger's battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
○ Since the built-in micro computer takes about
3 seconds to confi rm that the battery being charged with
UC18YSL3 is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.
MOUNTING AND OPERATION
Action
Inclined cutting using the guide
(+45° direction)
Fine tuning of parallelism
Fine tuning of perpendicularity
Fine tuning of guide piece position
Adjusting the cutting depth
Cutting line
Switch operation
About the mode select function
Remaining battery indicator
Using the LED light
Attaching the guide
Attaching the dust collection adapter
(sold separately)
Attaching the fl uorine plate
(sold separately)
Attaching the hook
*
(
2)
(sold separately)
Removing and inserting the battery
Charging
Cutting at right angles
Inclined cutting (+45° direction)
Holding the tool
Connection with cleaner
(sold separately)
About the link/independent switch
Link with unit
*
(
3)
Turn OFF link mode
Figure
Page
9
3
10
3
11
3
12
3
13
4
14
4
15
4
*
16
4
(
1)
17
4
18
4
19
5
20
5
21
5
22
6
23
6
24
6
25
6
26
7
27
7
28
7
29
8
30
9
31
10
Dismounting the saw blade
Mounting the saw blade
Charging a USB device from a
electrical outlet
Charging a USB device and battery
from a electrical outlet
How to recharge USB device
When charging of USB device is
completed
Selecting accessories
(*1) About the mode select function
Each time the mode selector switch is pushed, the
operation mode changes.
When Silent mode is selected, the Silent mode indicator
lamp lights up.
Silent mode reduces maximum motor RPM enabling
effi cient work with less noise.
If the load increases while the motor is operating in
Silent mode, it automatically changes to Power mode.
Additionally, if the load decreases again, it automatically
returns to Silent mode.
In Power mode, no change is made to Silent mode even
when the load decreases.
Mode
Power
Silent
NOTE
○ The mode will only change after a battery is installed and
the switch is pulled once.
○ The current mode will be maintained even if the switch is
on/off , or the battery is removed/reinserted.
(*2) Attaching the Hook
The hook can be used to hang up the unit temporarily
during operations (Fig. 22).
CAUTION
The hook should never be used to hang the unit on your
person.
When using the hook, check to make sure that the main
unit will not slip and fall, or become unstable by the wind,
etc.
Never hang the unit from your belt or trousers as this
could cause accidents.
(*3) Link with unit
NOTE
○ After both units begin searching (light blinking), it takes
approximately 1 to 3 seconds to complete connecting
(light on). Connection time may vary according to
distance or obstructions.
○ After switching on this product's power, approximately
0.5 seconds will be required for the dust extractor/
cordless cleaner to turn ON.
○ After switching on this product's power, approximately
0.5 seconds will be required for the dust extractor/
cordless cleaner to turn ON. When the unit is switched
OFF, a number of seconds will pass to allow the dust in
the hose to be sucked up before the unit shuts down.
○ While this product is searching (link mode display lamp
is blinking), pulling this product's switch will activate the
motor.
When the connection is completed (light on), the dust
extractor/cordless cleaner is switched ON.
○ While the dust extractor/cordless cleaner and this
product is in link mode, power will be automatically
switched off if neither is operated for two hours.
21
English
32
11
33
11
34-a
12
34-b
12
35
12
36
12
―
314
No-load speed
5000 min
-1
2600 min
-1
Publicidad
