Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
F F
e e
n n
d d
e e
r r
®
6
F F
e e
n n
d d
e e
r r
Your new 410 Pro SL Bass Loudspeaker Enclosure is
constructed from 3/4" (1.9 cm) 7-ply Birch/Maple
Plywood and is capable of handling 300 Watts of con-
tinuous power.
The 410 Pro SL features four 10"
(25.4 cm) speakers with 44 oz (1.25 kg) magnets and is
designed for use with a Fender
Bassman
®
1200, Bassman
or other professional quality bass amplifier. Please read
these instructions and the instructions that came with
your amplifier before making connections. Follow all
equipment caution and safety labeling.
SPEAKER CONNECTIONS
Use 16 gauge (or heavier) speaker cable with one of the
three types of input connections on your 410 Pro:
A) Phone jacks with a standard 1/4" plug
B) Binding posts with dual "banana" plug or
stripped wires
C) Speakon
®
connector with Speakon
Multiple 410 Pro SL cabinets can be linked as illustrat-
ed, when additional output is needed. Note: Follow the
speaker impedance load guidelines set by the manufac-
turer of your amplifier to avoid damage to your equip-
ment.
HORN TWEETER
The horn tweeter is protected from power-overload
damage by an incandescent lamp. If the horn tweeter
stops responding, replace the lamp as you would a
blown fuse.
The lamp and a spare (reorder
051857) are located on the circuit board on the inside
of the input jack panel.
Lamp Replacement:
1) Remove the 4 screws from the input jack panel cor-
ners.
2) Pull the panel out, then up.
3) Use a small flathead screwdriver to remove the
blown lamp which is visible through a cutout in the
circuit board.
4) Remove the spare lamp stowed on the side of the
circuit board and install it where the blown lamp was
located.
5) Install the input jack plate in the reverse order of
removal.
w
w w
w w
w . . f f e
e n
n d
d e
4 4
1 1
0 0
P P
r r
o o
S S
L L
L L
o o
u u
4 4
1 1
0 0
P P
r r
o o
S S
L L
L L
o o
u u
®
800 Pro,
®
300, Bassman
®
400 Head
®
plug
P/N
e r
r . . c
c o
o m
m
w w
w
d d
s s
p p
e e
a a
k k
e e
r r
E E
n n
c c
l l
o o
d d
s s
p p
e e
a a
k k
e e
r r
E E
n n
c c
l l
o o
SPECIFICATIONS
PART NUMBER:
DRIVERS:
CABINET:
SENSITIVITY:
POWER HANDLING:
IMPEDANCE:
CONNECTIONS:
ENCLOSURE VOLUME:
DIMENSIONS:
Height:
Width:
Depth:
WEIGHT:
Product specifications are subject to change without notice.
FENDER MUSICAL INSTRUMENTS CORP.
CORONA, CA USA
Fender
®
and Bassman
Speakon
®
is a registered trademark of Neutrik.
Copyright © 2003 FMIC
w w
w . . m
m r
r g
g e
s s
u u
r r
e e
s s
u u
r r
e e
2217000000
Four 10" (25.4 cm) Fender
Special Design Cast Frame
Woofers
2" (5.1 cm) Voice Coil, 44 oz
(1.25 kg) Magnet
One Horn Tweeter
1" (2.5 cm) Voice Coil, 8 oz
(0.23 kg) Magnet
3/4"
(1.9
cm)
Birch/Maple Plywood
94 dB, 1 Watt - 1 Meter
300 Watts, Continuous
600 Watts, Program
8Ω
Dual, Parallel Wired, 1/4"
High Current Input Jacks,
Binding
Posts
Speakon
®
Connector
V
= 4.4 ft
3
(125 l)
B
25.5 in
(64.8 cm)
25.5 in
(64.8 cm)
18.5 in
(47.0 cm)
78 lb
(35.5 kg)
A PRODUCT OF:
®
are registered trademarks of FMIC,
e a
a r
r h
h e
e a
a d
d . . n
7-ply
and
n e
e t
t
Publicidad
Tabla de contenido
