Bosch GLI 18V-1200 C Professional Manual Original página 12

12 | English
F) The signal range may vary greatly depending on external conditions, including the receiving device used. The Bluetooth® range may be signi-
ficantly weaker inside closed rooms and through metallic barriers (e.g. walls, shelving units, cases, etc.).
The colour rendition of illuminated objects can be distorted.
System Requirements
Mobile device (tablet, smart- Android 4.3 (and newer)
phone)
iOS 9 (and newer)
Fitting
Charging the battery (accessory)
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the Electronic Cell Protection (ECP). A protective circuit
switches the cordless worklight off when the battery is
drained.
Do not continue to press the On/Off switch after the
u
worklight has been automatically switched off. The
battery can be damaged. Ensure that the battery is
charged and that the worklight has cooled before switch-
ing on the worklight again.
To remove the battery (8), press the release button (7) (see
figure A) and pull the battery backwards and out of the cord-
less worklight. Do not use force to do this.
Follow the instructions on correct disposal.
Putting the button cell into operation
The cordless worklight is equipped with a button cell so that
it can be detected by the mobile device even if no battery
(8) is inserted, see figure A.
Remove the separating film between the button cell (10)
and the button cell contact when using the tool for the first
time.
Unlock the locking mechanism of the battery cover (6) and
fold up the battery cover (5).
Unscrew the screw of the battery compartment cover and re-
move the battery compartment cover (11). Remove the film
from the button cell contact and reattach the battery com-
partment cover with the screw.
Operation
Start-up
Inserting the Battery
Unlock the locking mechanism of the battery cover (6) and
fold up the battery cover (5).
Insert the charged battery (8) into the lamp head (1) until
you feel it engage and it is flush with the lamp head (1).
1 609 92A 3E4 | (27.04.2018)
Close the battery cover (5) and then the locking mechanism
of the battery cover (6).
Make sure that the rubber lip is seated correctly when
u
closing the battery cover. Otherwise protection against
dust and splash water will not be ensured.
Remove the battery cover
A very large battery will prevent the battery cover (5) from
closing. In this case, the battery cover can be removed.
Push the two hinges inwards against the spring force. Re-
move the battery cover.
To refit the battery cover, push the two hinges inwards
against the spring force again. Place the battery cover on the
housing. Allow the two hinge pins to engage in the openings
on the housing.
Setting up
Place the cordless worklight on a stable, level surface. Make
sure it is secure.
Hanging up
The notched carrying handle (3) can be used to hang up the
cordless worklight. Make sure it is hung up securely.
Fastening to the tripod
You can use the tripod mount (4) to screw the cordless
worklight onto a tripod.
Tighten the 1/4" screw. Ensure that the tripod has a firm
footing.
Switching on/off and adjusting the brightness
On/off switch Function
Press once Switches on the cordless worklight,
dimmed
Press twice Switches on the cordless worklight,
full brightness
Press three times Switches off the cordless worklight
If the cordless worklight has been switched on in dimmed
mode for approx. five minutes, it will be switched off imme-
diately the next time the button is pressed.
Temperature-dependent overload protection
When the permitted operating temperature is exceeded, the
cordless worklight initially reduces the brightness before
switching itself off if required for protection. Let the cordless
worklight cool down and then switch the cordless worklight
back on.
Changing the Button Cell (see figure A)
A warning will be displayed in the app before the button cell
is fully used up.
To change the button cell (10), unlock the locking mechan-
ism of the battery cover (6) and fold up the battery cover
(5), see figure A. Unscrew the screw of the battery compart-
ment cover (12) and remove the battery compartment cover
(11). Remove the empty button cell and insert a new button
Bosch Power Tools