Char-Broil 468101115 Instrucciones De Funcionamiento página 3

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 30
Safety Tips
Before opening gas cylinder valve, check the regulator for
tightness.
When appliance is not in use, turn off all control knobs and
gas.
Use long-handled barbecue utensils and oven mitts to
avoid burns and splatters. Use protective gloves when
handling hot components.
Maximum load for hotplate and side shelf is 4.5 Kg.
Cooking vessel minimum dia 200mm and maximum dia.
260 mm.
The grease cup (if equipped) must be inserted into
appliance and emptied after each use. Do not remove
grease cup until appliance has completely cooled.
Be very careful when you open the lid, since hot steam
may escape.
Be very careful when children, the elderly, or pets are
nearby.
If you notice grease or other hot material dripping from
appliance onto valve, hose or regulator, turn off gas supply
at once. Determine the cause, correct it, then clean and
inspect valve, hose, and regulator before continuing.
Perform a leak test.
Do not store objects or materials inside the appliance cart
enclosure that would block the flow of combustion air to the
underside of either the control panel or the firebox bowl.
DO NOT disconnect or change gas container within 3m of
an open flame or other ignition source.
Cylinder Placement
Cylinder cannot be placed under or in the appliance. Cylinders
are to be placed to the side and rear of the applaince. Cylinders
are to be a maximum diameter of 310mm and maximum height
of 600mm.
Regulator Requirements
A regulator must be used with this appliance. Use only gas
regulator supplied with your barbeque. If a regulator is not
supplied then use only regulator certified according to
EN12864 or EN16129 (Flow rate max. 1.5 kg/h) and approved
for your country and gas specified in Technical Data.
Hose Requirements
Use only approved hose which is certified to appropriate EN
standard and does not exceed 1.5m length. For Finland, the
hose length shall not exceed 1.2m.
Before each use, check to see if hoses are cut or worn. Make
sure hose is not kinked. Make sure that when connected hose
does not touch any warm surfaces. Replace damaged hoses
before using appliance. Replace hose as required by national
requirements.
Ignitor Lighting
• Do not lean over appliance while lighting.
1. Turn gas burner control valves to
2. Turn ON gas at cylinder.
3. Open lid during lighting.
4. To ignite, turn ignition burner knob to .
5. Push and hold ELECTRONIC IGNITION button.
6. If ignition does NOT occur in 5 seconds, turn the burner
controls
, wait 5 minutes and repeat lighting procedure.
7. Light adjacent burners in sequence by pushing knobs in and
turning to
. If ignitor does not work, follow match lighting
instructions.
WARNING
Turn controls and gas cylinder off when not in use.
Match Lighting
• Do not lean over appliance while lighting.
1. Open lid. Turn on gas at cylinder.
2. Place match into match holder, light match and place next to
burner ports. (Holder maybe on left or right side.)
3. Push in and turn burner knob to
sure burner lights and stays lit.
4. Light adjacent burners in sequence by pushing knobs in and
turning to
.
Hotplate Ignitor Lighting
• Do not lean over appliance while lighting.
1.Open hotplate lid. Turn on gas at cylinder.
2.Turn hotplate knob to
ELECTRONIC IGNITOR button.
3.If hotplate does NOT light, turn knob to
then repeat lighting procedure.
Hotplate Match Lighting
1.Open hotplate lid. Turn on gas at cylinder.
2.Place lit match near burner.
3.Turn hotplate knob to . Be sure burner lights and stays lit.
3
.
for burner being lit. Be
, push and hold
, wait 5 minutes,

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

468201115

Tabla de contenido