RST Milea Manual De Instrucciones Y Ensamble página 15

SAFE USE & MAINTENANCE OF PROPANE GAS BOTTLES
READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE GAS CYLINDER
When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST be observed.
FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION.
CYLINDER/ CONNECTOR REQUIREMENTS
1. Propane-gas cylinders, valves, and hoses must
be maintained and in good condition and must
be replaced if there is visible damage to either
the cylinder or valve. If the hose is cut or shows
excessive abrasion or wear, it must be replaced
before using the gas appliance (see 5).
2. This unit, when used with a cylinder, should
be connected to a standard 5-gallon (20 lb.)
propane gas cylinder equipped with an OPD
(Overfill Prevention Device). The OPD has been
required on all cylinders sold since October 1,
1998, to prevent overfilling.
3. Cylinder dimensions should be approximately
12" (30.5) cm in diameter and 18" (45.7 cm) high.
Cylinder must be constructed and marked in
accordance with the Specifications for Propane
Gas Cylinders of the U.S. Department of
Transportation (DOT) or the National Standard
of Canada, CAN/CSA-B-339, Cylinders, Spheres,
and Tubes for Transportation of Dangerous
Goods.
4. The cylinder used must include a collar to
protect the cylinder valve, and the cylinder
supply must be arranged for vapor withdrawal.
5. The pressure regulator and hose assembly
(figure 7-1) supplied with this outdoor cooking
gas appliance must be used. Original and
replacement pressure regulator and hose
assemblies must be those specified by the
manufacturer for connection with a cylinder
connecting device identified as Type I by the
ANSIZ21.58-2005/CGA 1.6-2005 (see PARTS LIST
for ordering information).
6. The propane gas cylinder valve must be
equipped with a cylinder connection coupling
device, described as Type I in the standard
defined in no. 5 above. This device is commonly
described as an Acme thread quick coupler.
7. If the propane gas cylinder comes with a dust
plug, place the dust cap on the cylinder valve
outlet whenever the cylinder is not in use.
QUICK COUPLER OPERATION
To connect the regulator/hose assembly to the
propane-gas cylinder valve fitting: Press the hand
nut on the regulator over the Acme thread fitting
on the cylinder valve. Turn the hand nut clockwise
to engage the threads and tighten until snug.
IMPORTANT FOR YOUR SAFETY
The use of pliers or a wrench should not be
necessary. Only cylinders marked "propane" may
be used.
To disconnect: Turn the hand-nut
counterclockwise until detached (Fig. 7.1).
Important: Before using the unit, and after each
time the cylinder is removed and reattached,
check the hose for wear (see no. 1) and check
all connections for leaks. Turn off the unit valves
and open the main cylinder valve, then check
connections with the soapy water. Repair any
leaks before lighting the unit.
CAUTION: Always turn the propane cylinder main
valve off after each use, and before moving the
unit and cylinder or disconnecting the coupling.
This valve must remain closed and the cylinder
disconnected while the appliance is not in use,
even though the gas flow is stopped by a safety
feature when the coupler is disconnected.
Carefully inspect the hose assembly each time
before the gas is turned on. A cracked or frayed
hose should be replaced immediately.
If the appliance is stored indoors, the
cylinder must be disconnected and removed.
Disconnected cylinders must be stored outdoors,
out of the reach of children, with threaded valve
plugs tightly installed, and must not be stored in
a building, garage, or any other enclosed area.
FOR YOUR SAFETY
14
1. DO NOT store a spare propane-gas cylinder
under or near this appliance.
2. NEVER fill the cylinder beyond 80-percent
full.
3. IF THE INFORMATION IN NO.1 AND NO.2 IS
NOT FOLLOWED EXACTLY, A FIRE CAUSING
DEATH OR SERIOUS INJURY MAY OCCUR.
FIG. 7-1