Robust RB-ID 550 Manual De Instrucciones página 16

Anleitung_RB_ID_550_SPK7__ 18.02.15 15:16 Seite 16
GB
Always pull the power plug before making
adjustments to the equipment.
6.1. Fitting the additional handle (Fig. 2-3/Item 8)
The additional handle (8) enables you to achieve
better stability whilst using the hammer drill. Do not
use the tool without the additional handle.
The additional handle (8) is secured to the hammer
drill by a clamp. During the handle clockwise tightens
this clamp. Turning it anti-clockwise will release the
clamp.
The supplied additional handle (8) must first be
n
fitted. To do this, the clamp must be opened by
turning the handle until it is wide enough for the
additional handle to be slid over the chuck (1)
and on to the hammer drill.
After you have positioned the additional handle
n
(8), turn it to the most comfortable working
position for you.
Now turn the handle in the opposite direction
n
again until the additional handle is secure.
The additional handle (8) is suitable for both left-
n
handed and right-handed users.
6.2 Fitting and adjusting the depth stop
(Fig. 4/Item 2)
The depth stop (2) is held in place by the additional
handle (8) by clamping. The clamp can be released
and tightened by turning the handle.
Release the clamp and fit the depth stop (2) in
n
the recess provided for it in the additional handle.
Set the depth stop (2) to the same level as the
n
drill bit.
Pull the depth stop back by the required drilling
n
depth.
Turn the handle on the additional handle (8) until
n
it is secure.
Now drill the hole until the depth stop (2) touches
n
the workpiece.
6.3 Fitting the drill bit (Fig. 5)
Always pull the power plug before making
n
adjustments to the equipment.
Release the depth stop as described in 6.2 and
n
push it towards the additional handle. This
provides free access to the chuck (1).
Undo the chuck by turning it
n
anti-clockwise with the supplied chuck key (9).
Select a suitable drill bit. Push the drill bit as far
n
as possible into the chuck opening.
Close the chuck (1). Check that the drill bit is
n
secure in the chuck (1).
Check at regular intervals that the drill bit or tool
n
is secure (pull the mains plug).
16
7. Operation
7.1 ON/OFF switch (Fig. 6/Item 5)
First fit a suitable drill bit into the tool (see 6.3).
n
Connect the mains plug to a suitable socket.
n
Position the drill in the position you wish to drill.
n
To switch on:
Press the ON/OFF switch (5)
Continuous operation:
Secure the ON/OFF switch (5) with the locking
button (4).
To switch off:
Press the ON/OFF switch (5) briefly.
7.2 Adjusting the speed (Fig. 6/Item 5)
You can infinitely vary the speed whilst using the
n
tool.
Select the speed by applying a greater or lesser
n
pressure to the ON/OFF switch (5).
Select the correct speed: The most suitable
n
speed depends on the workpiece, the type of use
and the drill bit used.
Low pressure on the ON/OFF switch (5): Lower
n
speed (suitable for: small screws and soft
materials)
Greater pressure on the ON/OFF switch (5):
n
Higher speed (suitable for large/long screws and
hard materials)
Tip: Start drilling holes at low speed. Then increase
the speed in stages.
Benefits:
The drill bit is easier to control when starting the
n
hole and will not slide away.
You avoid drilling messy holes (for example in
n
tiles).
7.3 Preselecting the speed (Fig. 6/Item 6)
The speed setting ring (6) enables you to define
n
the maximum speed. The ON/OFF switch (5) can
only be pressed to the defined maximum speed
setting.
Set the speed using the setting ring (6) on the
n
ON/OFF switch (5).
Do not attempt to make this setting whilst the drill
n
is in use.