Errebi LS8 Manual De Instrucciones página 15

reF. reSuLt on LS8
errebi
t33
T33 Texas-Cry 3GEN
FORD-Copy onTPX2.
PW: 03 ID: 80 81DCBE
MC: 01 LCK: 0010 DST40
T33 Texas-Cry 3GEN
FORD-Mire manual TP
PW: 03 ID: 80 FB4FA6
MC: 01 LCK: 0010 DST80
t34
T34 Texas-Cry 3GEN
TOYO-Mire Man.TP
PW: 37 ID: 96 3DF27F
MC: 80 LCK: 1111 DST40
TEXAS CRYPTO ++
Mire Manual tP
PW: 36 ID: 98 FAA182
MC: 80 LCK: 1111 DST80
tP35
T35 Texas-Cry 3GEN
TOYO-Copy onTPX2
PW: 33 ID: 0F 348CBC
MC: 0C LCK: 1111 DST40
if you have any problems or questions,
please contact technical support:.
If the key entered has a first generation Texas Crypto transponder that is
not recognised by the LS8 and thus does not appear in the above table, the
display will show the following message:
texas cryPto
coPy on tx2
PW: 00 ID: 00 30B5B9
MC: 02 LCK: 0010 DST40
the tX1 and tX4 can be programmed as many times as
desired. this is not the case with the tX2. because it is
an otP (one time programmable) transponder, it can only
be recorded once, after which it will be disabled for future
copies on the same transponder.
Similarly: if the key entered does not have a transponder, the display will
show the following advice message:
NO CHIP
NO TRANSPONDER
it must be mentioned that some high range cars,
bmW, merCedeS use a rolling code system (evolutionarily
encrypted), from the appearance of the first vehicles from around
1995, and although the machine shows that the copy is possible,
this cloning will not be valid because the codes constantly
evolve following an unknown protocol. avoid duplicating the
keys for vehicles with manufacturing dates after 1995.
aCtuaL tranSPonder
Texas Code Crypto. 2Gen. Wedge.
ford
Code example on a T33 / ID 6F-63
Texas Code Crypto. 3Gen. Wedge.
ford
Code example on a T33 / ID XX
Texas Code Crypto. 2Gen. Wedge.
toyota
Code example on a T34 / ID XX
Texas Code Crypto. 3Gen. Wedge.
toyota
CODE EXAMPLE ON A T34 / ID XX
texas code cryPto. 2gen. wedge
toyota
Code example on a T35 / ID 6F-70
ttexas code cryPto. wedge forMat.
Code example on a TXX / ID 6F-XX
4 .CoPying keyS
The steps to be followed in order to make a copy are:
4.1 LoCaL mode With no PC ConneCtion
•After entering the customer's original key in the antenna housing, press
the read button. A message will appear advising the transponder's ERREBI
type-reference that contains the original key read, as well as the transponder
on which ERREBI advises the duplicate.
Covers all fixed and most encrypted transponders (Texas/Philips). If the
transponders were encrypted from other brands such as Megamos or Temic,
the device will show the transponder's identification with its ERREBI reference
and will advise how to proceed to activate the key, generally redirecting to the
transponder's manual and the use of a programming machine (TRACK7).
•Next, and following the step-by-step indications on the display, the key is
removed and the new key entered on which the copy will be made together
with its corresponding transponder.
When making the copy, it is advisable to enter the key in a non-mechanical
manner, since due to the shavings or burrs that may remain on the key
that may interfere with the equipment's electronics if they fall through the
antenna or because the copy may be defective, it is preferable to cut the key
after successfully completing this section.
•Once the copy has been made, the device itself will indicate whether the
key is correct or erroneous.
In the case that more than one copy of the same key is required, repeat all
the steps in the previous paragraphs, keeping in mind that it is advisable
to use the original key provided by the customer as the base and the exact
transponder with the reference recommended by ERREBI as the "copy base".
The only exception is for the Philips Crypto, for which as many copies as
desired can be made without having to go through the entire process again.
4.1.1 inFormation viSibLe on the diSPLay in LoCaL
ConneCtion mode
When cloning the encrypted transponders, Texas as well as Philips, there is
no need for a connection to the PC or to the external cloning device coupling
(TPX Cloner + TX4TECH), given that in the LS8's new and compact design, all
functionalities have been included in one unit.
During initialisation, the following messages will be shown on the display:
ERREBI LS8
S/N: 0123456789ABCDEF
FWR: xx
CLR: TPx CLONER FOuND
The three first rows show the name, serial number and firmware version of
the LS8.
The last row shows, successively and alternately, the messages that
indicate whether or not the Texas and Philips encrypted transponder copy
functions are enabled.
The message "TPX Cloner Found" indicates that the LS8 is operational for
cloning the Texas Crypto.
Next, the "TX4TECH Found" message will appear, which indicates that the
LS8 is also operational for cloning the Philips Crypto.
Tx4TECH FOuND
TPH vER.: 39.1.6
Finally, after the message "TX4TECH found", the firmware version will be
displayed that controls the cloning of the Philips Crypto and which can be easily
updated using the CL USB port.