Publicidad
Idiomas disponibles
Idiomas disponibles
15.
MAIN MIX LEVEL LED Display
+10 LED only lights up occasionally. The optimal level is between -10 and 0 on the LED. If only the -30 LED
lights up or does not come on your S/N ratio will be degraded.
16.
MONITOR LEVEL – This adjusts the volume of the Monitor output.
17.
MASTER LEVEL –
18.
PHANTOM POWER – This switch activates and deactivates phantom power.
activated, phantom power supplies +48V to the XLR mic inputs and the LED above the switch
will be lit. Please note that most dynamic microphones do not require phantom power, while
most condenser microphones do. Consult your microphone's documentation to find out
whether it needs phantom power.
MASTER I/O (INPUT/OUTPUT)
19.
AMPLIFIER Mode Switch-
switch provides three modes:
MAIN/MAIN, MAIN/MONITOR and
BRIDGE. Select any one of these
modes to route the signals to the
corresponding jacks according to the
speaker panel connection. This
switch only affects the rear panel
outputs. The front panels outputs are
unaffected by this switch.
• MAIN/MAIN- When the switch is set to this, the amp will send the main mix to the rear panel Speakon
jacks or the rear panel ¼" jacks.
• MAIN/MON- When the switch is set to this, the amp will send the main mix to the OUTPUT 1 Speakon
jack and 1/4'"jack. The monitor mix will be sent to the OUTPUT 2 Speakon
• BRIDGE- When the switch is set to this, the amp will send the main mix to the rear panel OUTPUT 2
Speakon
jack.
™
20.
MAIN OUTPUTS – These 1/4" line level outputs can be connected to powered speakers or an amplifier
system. The level of these outputs is controlled by the Main Level knob.
21.
MONITOR OUTPUT- This line level
powered speaker.
22.
PHONES – Connect your 1/4" stereo headphones to this output.
23.
2-TRACK INPUTS – Connect these to the outputs of an external sound source using standard stereo RCA
cables (sold separately). You can send this to channels 9/10 (using the 2-TRACK to 9/10 switch) or to the main
outputs (using the 2-TRACK TO MAIN switch).
24.
2-TRACK OUTPUTS – You may connect these outputs to the inputs of an external recording device using a
standard stereo RCA cable (sold separately).
25.
AUX OUT- This outputs the line level signal sent from a channel's AUX1 Pre knob to the Monitor Output. You
can use it to feed the inputs of another stereo multi-effects unit (using a Y-type cable sold separately).
26.
STEREO RETURN- This stereo jack is used to route a stereo signal to the Main, Monitor
and Phones outputs by adjusting the FX TO MAIN and FX TO MON knobs.
27.
2-TRACK TO–
If you position this switch to the left you will route the signal fed into the
TAPE IN sockets into CH9~10 path, and the signal will be affected by channel level
control, channel EQ, DSP send, and MAIN level control. Positioning this switch to the
right will route the TAPE IN signal into Main mix bus. In this case signal will be affected
only by Main level control.
* Speakon is a trademark of Neutrik® AG, registered in the U.S. and other countries.
DSP (DIGITAL SIGNAL PROCESSOR)
28.
EFFECTS SELECTOR – Selects the effect that the mixer's internal effects processor will
apply to the various channels. Each channel can send different levels of audio to the
processor by adjusting their Aux 2/FX Post knobs.
29.
FX MUTE – Press this button to mute/unmute the effects.
30.
VARIATIONS SELECTOR – Selects the amount of the effect applied to the various
channels.
31.
Clip/Mute LED –
strong. When the digital effect module is muted, the LED also lights up.
32.
FX TO MON –
This is used to control the volume of the processed signal sent to Monitor
mix, which can be varied from - to +10dB.
33.
FX TO MAIN –
This is used to control the volume of the processed signal sent to Main
mix bus, which can be varied from - to +10dB.
34.
FOOTSWITCH – When a latching-style footswitch is connected to this jack with a 1/4"
TRS cable, it can be pressed to allow all channels to bypass the mixer's internal effects
processor.
–
This LED display will show you the Main mix output level. Make sure that the
This adjusts the overall volume of the MAIN output and HEADPHONE out.
This
balanced output is used to connect the input of an external amplifier or
This LED flashes when the signal input into the digital multi-effect is too
27
25
23
24
26
23
24
5
When
20
20
21
jack.
™
FX TO MAIN
FX TO MAIN
FOOTSWITCH
FOOTSWITCH
18
19
22
™
™
28
31
29
30
32
0
10
33
0
10
34
Publicidad
