Standard Accessories - Hitachi G 13VE Instrucciones De Manejo

6. To prolong the life of the machine and ensure a fi rst
class fi nish, it is important that the machine should not
be overloaded by applying too much pressure. In most
applications, the weight of the machine alone is suffi cient
for eff ective grinding. Too much pressure will result in
reduced rotational speed, inferior surface fi nish, and
overloading which could reduce the life of the machine.
7. The wheel continues to rotate after the tool is switched
off .
After switching off the machine, do not put it down until
the depressed center wheel has come to a complete
stop. Apart from avoiding serious accidents, this
precaution will reduce the amount of dust and swarf
sucked into the machine.
8. When the machine is not use, the power source should
be disconnected.
9. Be sure to switch OFF and disconnect the attachment
plug from the receptacle to avoid a serious accident
before the depressed center wheel is assembling and
disassembling.
10. When using the tool at any value except the full speed
(Dial scale 6), the motor cannot be suffi ciently cooled
due to the decreased number of revolution. This could
result in the risk of burning and damaging the motor
before an overload protective mechanism starts to
function.
Make sure that you use the tool by lightly applying it
to the surface of material when you use it at any value
except the full speed (Dial scale 6).
11. Caution when using near welding equipment
When using the grinder in the immediate vicinity of
welding equipment, the rotational speed may become
unstable. Do not use the grinder near welding equipment.
12. RCD
The use of a residual current device with a rated residual
current of 30 mA or less at all times is recommended.
NAMES OF PARTS (Fig. 1 – Fig. 8)
ⓐ
Push button
ⓑ
Side handle
ⓒ
Gear cover
ⓓ
Machine screw
Depressed center
ⓔ
wheel
ⓕ
Wheel washer
ⓖ
Wheel guard
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
G13VE: Disc Grinder
Read all safety warnings and all instructions.
Always wear eye protection.
ⓗ
Switch
ⓘ
Tail cover
ⓙ
Housing
ⓚ
Dial
ⓛ
Wrench
ⓜ
Wheel nut
ⓝ
Cutting wheel
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2002/96/
EC on waste electrical and electronic equipment
and its implementation in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
V Rated voltage
Alternating current
n
Rated speed
min Revolution or reciprocations per minute
-1
Switching ON
Switching OFF
Disconnect mains plug from electrical outlet
Warning
Class II tool

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package
contains the accessories listed in the below.
○ Wrench .........................................................................1
○ Side handle ...................................................................1
○ Depressed center wheel ...............................................1
Standard accessories are subject to change without notice.
APPLICATIONS
○ Removal of casting fi n and fi nishing of various types of
steel, bronze and aluminum materials and castings.
○ Grinding of welded sections or sections cut by means of
a cutting torch.
○ Grinding of synthetic resins, slate, brick, marble, etc.
○ Cutting of synthetic concrete, stone, brick, marble, and
similar materials.
SPECIFICATIONS
Model
Voltage (by areas)*
1
Power Input*
1
Rated speed
Outer dia.
Wheel Hole Dia.
Thickness
Peripheral speed
Weight*
2
*1 Be sure to check the nameplate on product as it is subject
to change by areas.
*2 Weight: According to EPTA-Procedure 01/2003
5
English
G13VE
(230 V)
1050 W
2800 – 10000 min -1
125 mm
22.23 mm
6 mm
80 m/s
2.1 kg