Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
English
A moment of inattention while operating power
tools may result in serious personal injury.
b)
Use personal protective equipment. Always
wear eye protection.
Protective equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing
protection used for appropriate conditions
will reduce personal injuries.
c)
Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool.
Carrying power tools with your finger on the
switch or energising power tools that have
the switch on invites accidents.
d)
Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part
of the power tool may result in personal injury.
e)
Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool
in unexpected situations.
f)
Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.
g)
If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
4)
Power tool use and care
a)
Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better
and safer at the rate for which it was designed.
b)
Do not use the power tool if the switch does
not turn it on and off.
Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c)
Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures reduce the
risk of starting the power tool accidentally.
d)
Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e)
Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool's operation.
If damaged, have the power tool repaired
before use.
4
Many accidents are caused by poorly
maintained power tools.
f)
Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g)
Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed.
Use of the power tool for operations different
from those intended could result in a
hazardous situation.
5)
Service
a)
Have your power tool serviced by a qualified
repair person using only identical
replacement parts.
This will ensure that the safety of the power
tool is maintained.
HEAT GUN SAFETY WARNINGS
WARNING:
1.
Do not use the tool or touch the power plug with
wet hands.
Failure to observe this may result in electric shocks.
2.
Always check the work area prior to use, and do
not use the tool if safety cannot be guaranteed.
Failure to observe this may result in inflammable
articles concealed in or behind invisible areas
(cases, ceilings, floors, hollow areas) being ignited.
3.
Do not use the tool in the vicinity of volatile
substances (thinner, gasoline, etc.)
Failure to observe this may result in the outbreak
of fire or explosions.
4.
Do not stand underneath when using the tool in
elevated locations.
Also, do not catch the power cord on anything, or
allow it to be pulled.
Failure to observe this may result in accidents.
5.
Do not point the hot wind directly at people or
animals. Do not look into the nozzle. Do not use it
as a hair dryer under any circumstances.
Failure to observe this may result in accidents or
injury.
6.
There are cases in which highly toxic gas will be
emitted if used on plastic, lacquer or similar
materials.
Always ensure that the work area is fully ventilated,
and wear a dust-protection mask.
7.
Apply heat gently while moving the Heat Gun up,
down, left and right.
Aiming it constantly at a single location may result
in the outbreak of smoke or fire.
8.
Check the tool for damage, cracks or malformation
in the event of it being accidently dropped or
subject to impact.
Damage, cracks and malformation may result in
injury.
Publicidad
Tabla de contenido
