Bosch GWX 15-125 PS Professional Manual Original página 19

A)
(11) X-LOCK fibre disc
(12) X-LOCK clip for fibre discs
(13) Protective guard for cutting
A)
(14) X-LOCK cutting disc
(15) X-LOCK holder
A)
(16) Hand guard
(17) X-LOCK cup brush/disc brush
A)
(18) Diamond core bit
(19) Handle (insulated gripping surface)
(20) Extraction guard for cutting with a guide block
A)
(21) Diamond cutting disc
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Angle grinder
Article number
Rated power input
Power output
Rated speed
Speed adjustment range
Max. grinding disc diameter
Speed preselection
Restart protection
Constant electronic control
Starting current limitation
Kickback stop
Weight according to EPTA-
Procedure 01:2014
– with additional low-vibra-
tion auxiliary handle
– with standard auxiliary
handle
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/Vibration Information
Noise emission values determined according to
EN 60745-2-3.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 91 dB(A); sound power level 102
dB(A). Uncertainty K = 3 dB.
Wear hearing protection
Total vibration values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
Surface grinding (roughing):
2 2
a = 5.0 m/s , K = 1.5 m/s ,
h
Bosch Power Tools
Grinding with abrasive disc:
a
A)
The vibration level given in these instructions has been
A)
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It can also
be used for a preliminary estimation of exposure to vibra-
tion.
The stated vibration level applies to the main applications of
A)
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
maintained, the vibration level may differ. This can signific-
antly increase the exposure to vibration over the total work-
A)
ing period.
To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not ac-
tually being used should also be taken into account. This can
significantly reduce the exposure to vibration over the total
working period.
Implement additional safety measures to protect the oper-
GWX 15-125 PS
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping the hands warm,
3 601 GB9 0..
and organising workflows correctly.
W 1500
W 820
Fitting
-1
min 11,500
-1
min 2800–11,500
Fitting protective equipment
mm 125
u
●
Note: If the grinding disc breaks during operation or the
●
holding fixtures on the protective guard/power tool become
●
damaged, the power tool must be sent to the after-sales ser-
●
vice immediately; see the "After-sales service and advice on
using products" section for addresses.
●
Protective guard for grinding
kg 2.5
kg 2.4
/ II
clicks into place.
Adjust the position of the protective guard (8) to meet the
requirements of the operation. To do this, push the unlock-
ing lever (1) upward and rotate the protective guard (8) into
the required position.
u
2 2
= 3.0 m/s , K = 1.5 m/s .
h
Pull the plug out of the socket before carrying out any
work on the power tool.
Place the protective guard
(8) onto the holder on the
power tool until the coding
cams of the protective
guard are aligned with the
holder. When doing so,
press and hold the unlock-
ing lever (1).
Press the protective guard
(8) onto the spindle collar
until the shoulder of the
protective guard is sitting
on the flange of the power
tool and rotate the protect-
ive guard until it audibly
Always position the protective guard (8) such that all
three red cams on the unlocking lever (1) engage in
English | 19
1 609 92A 4F9 | (10.01.2019)