Troubleshooting Guide; Common Audio/Visual Problems; Error Protection And Troubleshooting Guide - THOR PW Serie Manual Del Usario

TROUBLESHOOTING GUIDE

Common Audio/Visual Problems

PROBLEM
"Buzzing" sound in
audio systems
Television
Interference

Error Protection and Troubleshooting Guide

Display Indications, Common Problems, Possible Solutions / Indicacion, Causa Posible, Solucion Posible
LOW DC INPUT VOLTAGE (Below 10Vdc)
•
•
E 01
•
APAGADO DE BAJA ENTRADA DE VOLTAJE
•
•
•
HIGH DC INPUT VOLTAGE ( Above 16Vdc)
E 02
•
APAGADO DE ALTA ENTRADA DE VOLTAJE
•
OVERLOAD SHUTDOWN
•
•
E 03
•
APAGADO DE SOBRECARGA
•
•
•
OVER TEMPERATURE
•
E 04 •
APAGADO DE ALTA TEMPERATURA
•
•
•
GROUND FAULT PROTECTION / SHORT CIRCUIT PROTECTION
•
E 05
PROTECCION DE FUGA
•
•
•
No FUNCTION - (If inverter digital display does not illuminate.)
•
•
SOLUTION
Inexpensive stereo systems and "boom boxes" may emit a buzzing sound from their
speakers when operated from your inverter. This occurs because the power supply in
the electronic device does not adequately filter the pure sine wave produced by the
inverter. The only solution to this problem is to use a higher quality sound system.
Your inverter is shielded to minimize interference with TV signals. However, in some
instances, some interference may still occur, particularly where TV signals are weak.
Try the following corrective measures:
• Place the inverter as far as possible from the television. Use an extension cable, if
necessary.
• Readjust the orientation of the inverter, the antenna cables and the TV power cord to
minimize interference.
• Make sure the antenna feeding the television provides an adequate ("snow free")
signal and that high quality, shielded antenna cable is used.
• Do not use the inverter to operate high-power appliances or tools at the same time
you are using it to operate the TV.
• Make sure the inverter's case is properly grounded (refer to the "Permanent
Installation Procedure" section of this Instruction Manual).
Battery Voltage too low, Check or Recharge (battery) Power Source
Inadequate power being delivered to the inverter or excessive voltage drop. Use heavier gauge wire
See "Installation Speci cations" in users manual
Voltaje de la fuente (batería ) demasiado baja Recargue o substituya la ( batería) Fuente de alimentación
Potencia inadecuada entregado al inversor o excesiva caída de Voltage .
Consulte "Especi caciones de instalación" en el manual del usuario
Battery Voltage is too high, Check for fault with battery charging system
Voltaje de la batería es demasiado alto, Compruebe si hay fallas en el sistema de carga de la batería
Excessive start-up load. Power tool (or appliance ) draws too much voltage; and cannot be used with your inverter
Inadequate power being delivered to the inverter or excessive voltage drop . Use heavier Gauge wire.
See "Installation Speci cations" in users manual.
Excesivo Carga de arranque.
Potencia inadecuada entregado al inversor o excesiva caída de Voltage .
Consulte "Especi caciones de instalación" en el manual del usuario.
Inverter is too hot (thermal shutdown mode) Allow Inverter to cool. Check for adequate ventilation.
Reduce the load on the inverter to rated continuous output.
Inversor está demasiado caliente.
Permita inversor que se enfríe . Compruebe si hay una ventilación adecuada para el inversor .
Reduzca la carga en el inversor .
Inverter senses a leakage current on the ground terminal or short circuit current on the AC sockets. Unplug the AC appliance or
power tool. Turn o the inverter, disconnect unit from any 12 VDC power source. Check the appliance or power tool and cord.
Inversor detecta una corriente de fuga.
Inversor detecta corriente de cortocircuito.
Desenchufe el aparato de CA o herramienta eléctrica
Check and make sure the inverter is properly connected to (battery) Power Source .
See "Installation Speci cations" in users manual.
12