Thomashilfen RECARO Monza Reha Instrucciones De Montaje página 8

Turning plate with footrest adapter (accessory)
Before assembly, clean the plastic surface on the underside of the seat with commercially available cleaning agents (e.g. water and rinsing agent) until it is completely
free from grease. Now remove the Velcro strips (fleece) from the turning plate and attach them to the underside of the seat. The Velcro strips (hooks) remain on the turning
plate.
Position the seat flush in a 90° angle at the front of the turning plate (handle of the turning plate faces forwards) and tilt the seat over to velcro it to the turning plate.
The turning plate is pre-assembled for the attachment of the car seat on the right back seat of the vehicle (safe placing/removing of the child from the sideway in countries
with right hand traffic). If the car seat shall be fixed to the left back seat the pivotal point of the turning plate has to be changed. This is done by simply dislocating the
Allen screw.
Note: The audible clicking into place of the turning plate just serves as orientation aid for the straight positioning of the seat on the turning plate.
Transport: To transport the seat with turning plate, hold the handle of the turning plate with one hand and the back of the seat with the other. To reduce the load, seat and
turning plate can also be transported separately.
Footrest: The footrest is attached to the bottom part of the turning plate with the adapter. (see also page 27). The seat depth extension cannot be used in combination with
the turning plate.
Security advice!
Always place your child slowly and carefully in the seat - especially when using the turning plate! When turning the seat by 90° the pressure applied when placing/
removing the child may cause the backrest to abruptly fall backwards!
Fig. 6a: Attaching Velcro straps to the seat
Footrest, short 12 cm / 4.7" (accessory)
Footrest, long 18 cm / 7.1" (accessory)
Remove the two caps at the front bottom part of the seat before attaching the footrest. Press the catch springs in at the rear ends of the sliding rods and push the tubes into
the holes as far as they will go.
USA version only! Always lock the footrest to the seat with the screw provided with the user manual. The receiver for the screw is located underneath the seat.
To stabilize the footrest on the vehicle floor adjust the height of the support bars by screwing them in or out until they have contact with the vehicle. Then lock the
support bars with the hand knobs to prevent them unscrewing accidentally. Screw the hand knobs upwards as far as possible and tighten them fast.
Please note: If the turning plate is being used the footrest is attached to the footrest adapter integrated in the turning plate. In this case, make sure to always secure the
footrest against falling off with the hand knob provided with the user manual. The receiver for the hand knob (metal block with thread) is situated on the left tube of the
footrest adapter.
Lower leg length: The lower leg length is adjusted by changing the height of the footrest. Loosen both outer knurled nuts. Retighten them after each adjustment.
Foot angle: Loosen the four screws left and right on the underside of the footrest to adjust the desired foot angle with the rails. Then retighten the screws.
Please note: The footrest cannot be used in combination with the seat depth extension.
Fig. 7a: Caps + inserting the footrest
Seat wedge, bottom (accessory)
The seat wedge is positioned centrically below the car seat. The high edge is at the front to achieve an optimum rest position of the child.
The cover can be removed (zipper) and washed in the machine at up to 30° C / 86° F.
Please note: Function of the turning plate is considerably reduced if being used in combination with the seat wedge. We therefore do not recommend using seat wedge
and turning plate at the same time.
Fig. 8a: Positioning seat on seat wedge
Seat wedge, inside (accessory)
The seat wedge (inside) can be fastened to the seat surface at 3 different positions:
1. An active posture is achieved by placing the seat wedge on the seat with the high side facing the back.
2. Velcro-fasten the seat wedge with the flat side facing rearwards for a more passive posture / rest position.
3. In order to reduce the seat depth or to achieve a bigger hip angle, you can also Velcro-fasten the seat wedge to the rear of the seat in an upright position with the broad
side facing downwards.
The two lateral pads for additional protection are Velcro-fastened to the sides.
The cover can be removed (zipper) and washed in the machine at up to 30° C / 86° F.
Fig. 9a: active Fig. 9b: passive
Seat depth extension + 13 cm / 5.1" (accessory)
USA version only! Attention: Before assembly of the seat depth extension, attach the safety screw provided with the user manual to the thread on the underside of the
seat. Before removing the seat depth extension, make sure to remove this safety screw again.
Remove the two caps at the front bottom part of the seat before attaching the seat depth extension. Press the catch springs in at the rear ends of the sliding rods and push
the tubes into the holes as far as they will go.
Please note: The seat depth extension cannot be used in combination with the footrest or turning plate.
The cover can be removed (cord) and washed in the machine at up to 30° C / 86° F.
Fig. 10a: Removing caps
Table (accessory)
Slide the table onto the two sides of the seat surface. The table is fastened on both sides with two Velcro strips each. Guide the Velcro strips of the table through the
plastic rings at the seat / seat back (pelvic belt).
The cover can be removed (zipper) and washed in the machine at up to 30° C / 86° F.
Fig. 11a: Attaching the table
8
RECARO Monza Reha – Instructions for assembly and use (addition)
Fig. 6b: Attaching seat to turning plate / dislocating the Allen screw
Fig. 7b: Adjusting height to vehicle
Fig. 8b: Final position
Fig. 9c: back Fig. 9d: with lateral pads
Fig. 10b: Pressing in the catch springs
Fig. 11b: Attaching belts to seat
item code: 812
item code: 806
item code: 805
item code: 810
item code: 809
item code: 808
item code: 811