Before Starting The Equipment - EINHELL TC-BG 150 Manual De Instrucciones Original

1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Pull the power plug before doing any mainte-
nance or assembly work on the equipment.
•
The equipment has to be set up where it can
stand securely.
•
Before starting work, firmly screw the grin-
ding/sanding machine to the workbench or
equivalent using the 4 mounting holes (8) in
the base plate (9).
•
All covers and safety devices have to be pro-
perly fitted before the equipment is switched
on.
•
It must be possible for the grinding/sanding
wheel to run freely.
•
Check that the voltage on the rating plate is
the same as your supply voltage before you
connect the equipment to the power supply.
5.1 Assembling the spark defl ector / safety
window (Fig. 3/4)
•
Fasten the spark deflector (3) to the machine
(Fig. 3).
•
To do this, use the socket head screws (11),
washers (12), spring washers (13) and nuts
(14).
•
Tighten the screw connection using a 4 mm
hex key and an 8 mm wrench. Note! Not
supplied.
•
Fit the safety window (2) to the spark deflec-
tor (3) using a lock screw (15), a washer (12),
a spring washer (13) and a locking button
(16) (Fig. 4).
Anl_TC-BG_150_SPK9.indb 21 Anl_TC-BG_150_SPK9.indb 21
GB
5.2 Adjusting the spark defl ector (Fig. 5)
•
With the help of the slots in the spark deflec-
tor (3) you can adjust it in vertical direction.
•
To do so, slacken the socket head screws
(11) and push the spark deflector as close as
possible to the grinding/sanding wheel (5, 6).
•
Warning! The distance between the grinding/
sanding wheel (5, 6) and the spark deflector
(3) must be set as small as possible and un-
der no circumstances should it exceed 2 mm.
•
Then secure the spark deflector (3) again.
•
Warning! Adjust the spark deflector (3) peri-
odically to compensate for wear on the grin-
ding/sanding wheel (5, 6).
5.3 Fitting the workpiece support (Fig. 6)
•
Fit the workpiece support (7) to the machine.
•
Warning! The angled face of the workpiece
support must point away from the grinding/
sanding wheel (5, 6)!
•
To achieve this, use the lock screw (17), the
washer (18), the spring washer (19) and the
locking button (20).
5.4 Setting the workpiece support (Fig. 7)
•
With the help of the slot in the workpiece
support (7) you can adjust it in horizontal
direction.
•
To do so, slacken the locking button (20) and
push the workpiece support (7) as close as
possible to the grinding/sanding wheel (5, 6).
•
Warning! The distance between the grinding/
sanding wheel (5, 6) and the workpiece sup-
port (7) must be set as small as possible and
under no circumstances should it exceed 2
mm.
•
Then secure the workpiece support (7) again
with the locking button (20).
•
Warning! Adjust the workpiece support (7)
periodically to compensate for wear on the
grinding/sanding wheel (5, 6).
5.5 Changing the grinding/sanding wheel
(Fig. 8-12)
•
Before replacing the grinding/sanding wheel:
Pull out the power plug!
•
Undo the 3 screws (A) on the cover (4) using
the 4 mm hex key. Pull out the screws (A) as
far as they will go.
•
Now turn the left-hand cover (4) counterclock-
wise to the point where the cover (4) can be
removed past the spark deflector (3). Turn the
right-hand cover (4) clockwise.
•
Remove the cover (4).
•
Slacken the socket head screws (11) as de-
- 21 -
16.06.2020 15:18:28 16.06.2020 15:18:28