Tabla de contenido
Publicidad
OPERATING INSTRUCTIONS
5.
Carefully clear away any excess
dust or debris from agitator.
6.
Remove agitator from housing
starting on the left side followed by
the right side.
7.
If the belt has broken, remove any
loose pieces before replacing with
a new belt.
8.
Remove the worn or broken belt
from the motor drive shaft.
9.
Loop the new belt first over the
drive shaft then over agitator into
the groove on the right side of the
agitator. (Fig. 11)
10. Insert the right side of the agitator
by placing the end cap down into
the slot on the housing and then
align the left side. Press down
firmly to make sure that each end
of the agitator is correctly fitted
into the slots.
Motor
Belt
Agitator
Fig. 11
NOTE: There will be some tension on
the belt as the agitator is being put into
place.
11. Make sure that the belt is centered
on the pulley and the agitator
turns.
12. Replace the front end of the top
cover ensuring the wheel hubs fit
properly in place. (Fig 12)
13. Lift handle to secure top cover
over carpet height selector.
14. Drop handle so that the vacuum is
laying flat again. Holding the top
and bottom of unit gently turn unit
over and replace the screws. Do
not turn the screws too tightly to
avoid stripping the screw holes.
Fig. 12
Wheel Hub
Storage
To store the vacuum cleaner, put it in
the upright position. Turn the power
"Off". Remove the power cord from the
electrical outlet. Press the cord rewind
button. If the cord does not fully retract,
pull it out again and then press on cord
rewind button.
Warning:
Hold the plug when
rewinding the cord. Do not allow the
cord to whip when rewinding.
Note:
Before using the appliance,
unwind a sufficient length of cable and
Insert the plug into the wall socket. A
yellow mark on the power cord shows the
ideal cable length. Don't pull the power
cord beyond the red mark.
Motor Thermostat
Important:
This unit is equipped
with a motor protective thermostat. If
for some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:
• Push the On/Off button once.
• Disconnect the plug from the power
source.
• Check the source of overheating
problem. (i.e. clogged hose or filter)
• If clogged hose or filter is found,
unclog the hose and replace the
filters.
• Wait at least 45 minutes before
attempting to reuse the vacuum.
• After unit has cooled down for 45
minutes, plug in the cleaner and
push the On/Off button. The
vacuum should start again.
• If the vacuum still does not start,
contact customer service at
1 (800) 798-7398.
8
FAMILIARISEZ-VOUS AVEC VOTRE MINI ASPIRATEUR
VERTICAL
1. Poignée
2. Poignée télescopique
3. Bouton de réglage de la hauteur
du tube télescopique
4. Bouton d'alimentation On/Off
5. Bouton de relâche de la coupelle
6. Coupelle à poussière (réservoir)
7. Bouton de réglage de hauteur de
tapis
8. Électrobrosse
Spécifications techniques
Tension :
120 V, 60 Hz
Intensité :
12 A
Avertissement: Les illustrations peuvent différer de l'appareil lui-même.
9. Pédale de relâche de la poignée
10. Bouton de rembobinage du cordon
11. Entrée de tuyau
12. Boyau souple
13. Pince du cordon d'alimentation
14. Bouton de relâche du tube
télescopique
15. Suceur plat
16. Brosse à épousseter
17. Cordon d'alimentation
18. Raccord de tuyau
25
Publicidad
Tabla de contenido
