Publicidad
Idiomas disponibles
Idiomas disponibles
Installation of the Speaker Outputs
The speaker cables should be polarized (marked) so that you can easily identify which is positive and which is negative.
Minimum gauge is 13 AWG. Keep the cables well insulated and avoid metal parts as these may damage the insulation.
• WITH 2 SPEAKERS
SPEAKER
HL 1000.2 (2 OHMS):
2 x 2 OHMS
• BRIDGE (WOOFER/SUBWOOFER)
SPEAKER
HL 1000.2 (2 OHMS):
1 x 4 OHMS
• STEREO + BRIDGE
SPEAKER
1
8
HL 1000.2 (2 OHMS):
2
STEREO + BRIDGE:
1 x 8 Ohms (SUPER TWEETER)
1 x 8 Ohms (DRIVER)
BRIDGE: 1 x 4 OHMS (WOOFER)
Bipolarity Capacitor: 47 μF / 100V
1
Polyester Capacitor 2,2 μF / 250V
2
Troubleshooting
NO POWER
• The power cables are not connected correctly (terminals +BAT, GND and REM). Verify that all the connections have
electrical and mechanical contact.
• The fuse/circuit breakers are defective or blown. Replace them, making sure that the replacements are the correct
ones!
NO SOUND
• The speaker cables or RCA plugs are not connected correctly.
• Check to see if the LEVEL control is at the lowest setting.
• Check the amplifier filter controls.
NO SOUND. RED ALERT PROT BLINKING:
• The speakers or cables are defective. Check speakers, cables and connections.
POOR SOUND QUALITY (DISTORTIONS):
• The speakers are overloaded. Decrease and readjust the volume level (see entry "LEVEL (LEVEL CONTROL)")
WEAK BASS:
• Speaker cables (+) and (-) are switched or the speaker is out of phase (see entry "INSTALLATION OF THE SPEAKER
OUTPUTS").
• Also check audio control level.
ENGINE, HORN, TURN SIGNAL, INTERFERENCE:
• Use suppressing/insulated cables on the spark plugs.
• Use capacitors on the alternator, horn and ignition.
• Run the shielded input cable away from any other cables, as they are particularly prone to interference.
• Install a separate power source (+12V) for the sound system. Use a fuse/circuit breaker 30 centimeters from the bat-
tery as a safety precaution.
• Ground the amplifier properly. Remove paint from the chassis at the selected point and connect the wire using a
grounded terminal. In order to prevent rust, insulate it with paint.
• Do not loop the ground. Avoid using multiple grounds. If possible, use a star connection in which all the grounds run
from a single point.
Technical Specifications
Channels:
Power @ 14.4V - STEREO 2 Ohms (RMS):
Power @ 14.4V - STEREO 4 Ohms (RMS):
Power @ 14.4V - BRIDGE 4 Ohms (RMS):
Power @ 12.6V - STEREO 2 Ohms (RMS):
Power @ 12.6V - STEREO 4 Ohms (RMS):
Power @ 12.6V - BRIDGE 4 Ohms (RMS):
Min. Output Impedance STEREO:
Min. Output Impedance BRIDGE:
Input Impedance:
Input Sensitivity:
T.H.D:
Signal to Noise Ratio:
Freq. Resp. (-3dB) @ 1 Ohm:
Crossover Low Pass:
Crossover High Pass:
Bass Boost:
Power Supply:
Consumption Music (12,6V):
Consumption BASS (12,6V):
Dimensions (H x W x L):
Weight:
Any updates made in this manual will be available for consumers to consult without any charge on the brand's site.
It is recommended that the updated manual be consulted whenever necessary.
EU Declaration of Conformity (DoC):
www.stetsom.com.br/certifications/HL1000_2_stamped_signed.pdf
HL 1000.2 / 2 OHMS
2
2 x 560W
2 x 340W
1 x 1120W
2 x 500W
2 x 280W
1 x 1000W
2 OHMS
4 OHMS
15K OHMS
0,2 V
> 0,4 % THD
> 90 dB
10 Hz ~ 22 KHz
60 Hz ~ 2,2 KHz
60 Hz ~ 2,2 KHz
+20 dB
9 ~ 15 V
45 A
90 A
66 x 206 x 156 mm
1.35 Kg
9
Publicidad
