Stanley FATMAX KFMCD607 Manual De Instrucciones página 6

ENGLISH
Open the chuck by turning it (4) with one hand while
u
holding the tool with the other.
Insert the bit shaft into the chuck.
u
Firmly tighten the chuck by turning it (4) with one hand
u
while holding the tool with the other.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Charging the battery (fig. A)
The battery needs to be charged before first use and
whenever it fails to produce sufficient power on jobs that were
easily done before. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 0 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell
temperature warms up or cools down.
To charge the battery (8), insert it into the charger (13).
u
The battery will only fit into the charger in one way. Do not
force. Be sure that the battery is fully seated in the
charger.
Plug in the charger and switch on at the mains.
u
The charging indicator (14) will flash green (slowly).
The charge is complete when the charging indicator (14) lights
green continuously. The charger and the battery can be left
connected indefinitely with the LED illuminated. The LED will
change to flashing green (charging) state as the charger
occasionally tops up the battery charge. The charging
indicator (14) will be lit as long as the battery is connected to
the plugged-in charger.
Charge discharged batteries within 1 week. Battery life will
u
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Charger diagnostics
If the charger detects a weak or damaged battery, the
charging indicator (14) will flash red at a fast rate. Proceed as
follows:
Re-insert the battery (8).
u
6
(Original instructions)
If the charging indicators continues flashing red at a fast
u
rate, use a different battery to determine if the charging
process works properly.
If the replaced battery charges correctly, the original
u
battery is defective and should be returned to a service
centre for recycling.
If the new battery gives the same indication as the original
u
battery, take the charger to be tested at an authorised
services centre.
Note: It may take as long as 60 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink red, fast and slow, one
flash at each speed and repeat.
Selecting the direction of rotation (fig. C)
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
To select forward rotation, push the forward/reverse slider
u
(2) to the left.
To select reverse rotation, push the forward/reverse slider
u
to the right.
To lock the tool, set the forward/reverse slider into the
u
centre position.
Selecting the operating mode or torque (fig. D)
The KFMCD607's transmission allows the user to switch
between drill mode and drive mode without changing the
clutch collar's clutch setting. The user can switch to drill
mode, drill a pilot hole. Then rotate into drive mode with one
click , and use whatever clutch setting they have set. Large
screws and hard workpiece materials require a higher torque
setting than small screws and soft workpiece materials. The
collar has a wide range of settings to suit your application.
For drilling in wood, metal and plastics, set the collar (5) to
u
the drilling position by aligning the symbol with the
marking (16).
For screwdriving, set the collar to the desired setting. If
u
you do not yet know the appropriate setting, proceed as
follows:
Turn the mode select collar (5) until the marking (16) is
u
aligned with the screw icon
Set the collar (3) to the lowest torque setting.
u
Tighten the first screw.
u
If the clutch ratchets before the desired result is
u
achieved, increase the collar setting and continue
tightening the screw. Repeat until you reach the correct
setting. Use this setting for the remaining screws.
Speed selector (fig. E)
For drilling in steel and for screwdriving applications, slide
u
the speed selector 6) towards the rear of the tool (1st
gear).