Black and Decker Powerful Solutions SMS216 Manual Del Usuario página 14

ENGLISH
changing the blades. Use correctly sharpened saw blades.
Observe the maximum speed and tooth type marked on the
saw blade. Only use Black & Decker recommended blades.
To replace the blade (24), proceed as follows:
Using a screwdriver, loosen but do not remove the
screw (37). Do not remove the screw completely as it
will make re-assembly difficult.
Using a screwdriver, loosen but do not remove the
screw (38). Do not remove the screw completely as it
will make re-assembly difficult.
Press the saw arm release lever (26) and rotate the
moveable lower guard (4) counter clockwise and clear
of the blade. Use one hand to hold the guard in place
(fig. O).
Move the spindle guard plate (40) counter clockwise
(fig. O) to give you access to the spindle bolt (39) that
attaches the blade to the mitre saw.
Press the spindle lock button (41) which is located on
the motor housing to lock the saw blade and prevent it
from rotating.
Using the supplied blade spanner, turn the spindle
bolt (39) in a clockwise direction to remove the bolt and
the blade (24).
Fit a replacement blade, make sure that the teeth are
pointing downward and the direction marking on the
blade is the same as that on the mitre saws guard
(clockwise) (fig O).
Loosely fit the spindle bolt (39) by hand and turn counter
clockwise.
Press the spindle lock button (41) which is located on
the motor housing to lock the saw blade and prevent it
from rotating.
Use the blade spanner to tighten the spindle bolt (39)
until the blade is secure.
Allow the moveable lower guard (4) to return to its
original position covering the blade.
Move the spindle guard plate (40) into its original
position and tighten the two screws (37 and 38).
Warning! Never press the spindle lock while the blade is
rotating. Be sure to hold the guard bracket down and firmly
tighten the guard bracket screw after installing the blade.
Warning! The guard bracket must be returned to its original
position and the screw tightened before activating the saw.
Failure to do so may allow the guard to contact the spinning
saw blade resulting in damage to the saw and severe
personal injury.
14
Accessories
The performance of your tool depends on the accessory
used. Black & Decker and Piranha accessories are
engineered to high quality standards and designed to
enhance the performance of your tool. By using these
accessories you will get the very best from your tool.
Warning! Do not carry the machine by the guard.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning. Regularly clean the ventilation slots with a
clean, dry paint brush. To clean the tool, use only mild soap
and a damp cloth. Never let any liquid get inside the tool and
never immerse any part of the tool into liquid.
Warning! To reduce the risk of injury, turn the unit off and
disconnect the tool from the power source before installing
and removing accessories, before adjusting or changing set-
ups or when making repairs. Be sure the trigger switch is in
the OFF position. An accidental start-up can cause injury.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
Connect the brown lead to the live terminal in the new
plug.
Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 13 A.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again. Re-
use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.