Technical Data; Brief Description - Felisatti PF110/1100S Instrucciones De Servicio

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 6
Planes
Absorbed power
No-load speed
Cutting depth
Total cut width
Rebate's depth
Approx. weight (without accessories)
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept
close at hand to use when carrying out maintenance on the
indicated parts.
If the tool is used with care and normal maintenance is carried
out, it will work well for a long time.
The functions and use of the tool you have bought shall be
only those described in this manual. Any other use of the
tool is strictly forbidden.
PLANER SAFETY RULES
Planer Safety Rules
- Wait for the cutter to stop before setting the tool down. An
exposed cutter may engage the surface leading to possible
loss of control and serious injury.
- Do not reach into the saw dust ejector with your hands.
They could be injured by rotating parts.
- Apply the machine to the workpiece only when switched on.
Otherwise there is danger of kickback when the cutting tool
jams in the workpiece.
- When working, always hold the planer in such a manner that
the planer base plate faces flat on the workpiece. Otherwise
the planer can become wedged and lead to injuries.
- Never plane over metal objects, nails or screws. The planer
blade and the blade shaft can become damaged and lead to
increased vibrations.
- Secure the workpiece. A workpiece clamped with clamping
devices or in a vice is held more secure than by hand.
- Never use the machine with a damaged cable.
Do not touch the damaged cable and pull the mains plug
when the cable is damaged while working. Damaged cables
increase the risk of an electric shock.
Products sold in GB only: Your product is fitted with an BS
16/A approved electric plug with internal fuse (ASTA
approved to BS 16).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 0 mA or less.
ILLUSTRATIONS
A Safety push button switch (Fig. 1)
B On-/off switch (Fig. )
E Drive wheel (Fig. 5)
F Toothed belt (Fig. 5)
G Idler pulley (Fig. 5)
I Side end-stop immobilisation control (Fig. 1 and 4)
J Circular depth graduation scale (Fig. 1)

TECHNICAL DATA

PF110/1100S
W
1100
/min
16000
mm
0-
mm
110
mm
-
Kg
4,0
K Depth graduation handle (Fig. 1)
L Lateral stop (Fig. 1)
M Sawdust extraction (Fig. )
N Cope depth end-stop (Fig. )
O Blade replacement screws (Fig. 6)
P Guide slot (Fig. )
Q Toothed belt cover (Fig. 5)
R Toothed belt cover screw (Fig. 5)
S Mobile plate (Fig. )
T Dust suction adapter (Fig. 1)
U Base plate (Fig. )
- Dust suction adapter
- Hexagonal key
- Lateral stop
- Depth end-stop
- Operating instructions
- Safety instructions
- Warranty
This tool has been designed to rout wood and similar
materials, to plane irregular surfaces and to cant off edges.
Before using the tool, make sure the mains voltage is correct: it
must be the same as that on the specification label. Machines
with 0V can also be connected to a 0-V mains supply.
WARNING! Only plug in when machine is switched off. Press
the locking button A, and squeeze the trigger in the on/off
switch B. When the on/off switch is released, the machine
stops.
For safety reasons, it is not possible to lock On/Off switch
B, instead it has to be pressed while the machine is being
used.
1. Planing depth
WARNING! Always unplug the machine before carrying out
work on it.
Regulate the cutting depth, from 0-/,5mm. without
gradations, turning the handle K. Fig. 1, making out the value
in the scales J.
2. Surface planing
WARNING! The plane should only be applied to the work-
piece in the switched-on position.
Position the machine with the front section of mobile plate
S over the work-piece. During surface planing (wood beams
and tables etc) mobile plate S and base plate U should
always rest on the entire work surface (danger of blade
repercussion). The blade should be guided with both hands
and moved forward in a uniform fashion over the work
PF110/2000S
000
15000
0-,5
EQUIPMENT

BRIEF DESCRIPTION

BEFORE USING THIS TOOL
START UP
OPERATING INSTRUCTIONS
110
16
7,


Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Pf110/2000s

Tabla de contenido