Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
CONTENTS
Hood Protector
Instructions Sheet
Alcohol Wipe
Screwplugs
Large Screws
Large Washers
Rust Inhibitor
IMPORTANT: Read all instructions carefully before
beginning the installation.
HELPFUL HINT
Ensure to use caution when drilling holes in
underside of hood.
STEP 1
Thoroughly clean and dry the hood prior to installation.
Open the hood and trial fit the Hood Protector centrally
onto hood. Note & mark the slots in the Hood Protector
tag that corresponds to the underside of hood. Also note
the wing clip hole positions in relation to the hood lip. Mark
these positions with a non-permanent marker or pencil.
Remove the Hood Protector. See FIGURE 1.
STEP 2
At the previously marked tag locations. Carefully drill the
underside of hood using a 3/16" or 5mm drill bit. Do this for
the 4 locations. See FIGURE 2. FAILURE TO DO THIS
MAY RESULT IN PERMANENT DAMAGE TO THE TOP
SIDE OF THE HOOD.
STEP 3
Apply the rust inhibitor to the exposed edges of holes in
hood, as shown. See FIGURE 3.
STEP 4
Insert the white screwplugs provided into the previously
noted vacant holes, as shown. See FIGURE 4.
x1
x1
x1
x4
x4
x4
x1
1
2
3
4
SUP268
1/6
82209649
Publicidad
Manuales relacionados para Jeep K6859578
Resumen de contenidos para Jeep K6859578
- Página 1 SUP268 82209649 CONTENTS Hood Protector Instructions Sheet Alcohol Wipe Screwplugs Large Screws Large Washers Rust Inhibitor IMPORTANT: Read all instructions carefully before beginning the installation. HELPFUL HINT Ensure to use caution when drilling holes in underside of hood. STEP 1 Thoroughly clean and dry the hood prior to installation.
- Página 2 SUP268 82209649 STEP 5 Re-install Hood Protector onto hood. Ensure that the boss heads of the screwplugs locate into the slots in the Hood Protector tags. Centralize and secure Hood Protector to hood using the large screws and large washers provided. See FIGURE 5.
- Página 3 SUP268 82209649 CONTENIDO Hood Protector Hoja De Instrucciones x1 Trapo Del Alcohol Enchufes de tornillo Tornillos Grande Arandelas Grande Inhibidor De Moho IMPORTANTE: Lea todas las instrucciones cuidadosamente antes de comenzar la instalación. INDIRECTA PROVECHOSA Asegúrese a la precaución del uso al perforar los agujeros en el superficie inferior de la capilla.
- Página 4 SUP268 82209649 PASO 5 Reinstale el protector de la capilla sobre la capilla. Asegúrese de que los jefes del jefe de los screwplugs localicen en las ranuras en las etiquetas del protector de la capilla. Centralice y asegure el protector de la capilla a la capilla usando los tornillos grandes y las arandelas grandes proporcionados.
- Página 5 SUP268 82209649 CONTENTE Hood Protector Instructions Sheet L’alcool Wipe Prises de Vis Grandes Vis Grandes Rondelles Agent Antirouille IMPORTANT : Lisez toutes les instructions soigneusement avant de commencer l’installation. CONSEIL UTILE. Assurez à l’attention d’utilisation en forant des trous dans le dessous du capot. ÉTAPE 1 Complètement propre...
- Página 6 SUP268 82209649 ÉTAPE 5 Réinstallez le protecteur de capot sur le capot. Assurez- vous que les têtes de patron des screwplugs placent dans les fentes dans les étiquettes de protecteur de capot. Centralisez et fixez le protecteur de capot au capot en utilisant les grandes vis et les grandes rondelles fournies.