Installation; Positioning And Levelling; Connecting The Water And Electricity Supplies - Indesit DFP 2631M Manual De Instrucciones

Installation

Keep this instruction manual in a safe place for future
EN
reference. If the appliance is sold, given away or moved, please
ensure the manual is kept with the machine, so that the new
owner may benefit from the advice contained within it.
Please read this instruction manual carefully: it contains
important information regarding the safe installation, use and
maintenance of the appliance.
If the appliance must be moved at any time, keep it in an
upright position; if absolutely necessary, it may be tilted onto its
back.
This appliance is intended to be used in household and similar
applications such as:
- staff kitchen areas in shops, offices and other working
environments;
- farm houses;
- by clients in hotels, motels and other residential type
environments;
- bed and breakfast type environments.

Positioning and levelling

1. Remove the appliance from all packaging and check that it has
not been damaged during transportation.
If it has been damaged, contact the retailer and do not proceed
any further with the installation process.
2. Check the dishwasher by placing it so that its sides or back
panel are in contact with the adjacent cabinets or even with the
wall. This appliance can also be recessed under a single worktop
( see the Assembly instruction sheet ).
3. Position the dishwasher on a level and sturdy floor. If the floor
is uneven, the front feet of the appliance may be adjusted until it
reaches a horizontal position. If the appliance is levelled correctly,
it will be more stable and much less likely to move or cause
vibrations and noise while it is operating.
*
4 . Adjust the height of the rear foot from the front of the appliance
on the central lower part of the dishwasher, turning a hexagonal
spanner (red color) with an opening of 8 mm in a clockwise
direction to increase the height or in an anticlockwise direction to
decrease the height.
Connecting the water and electricity
supplies
Connection to the water and electricity supplies should only
be performed by a qualified technician.
The dishwasher should not stand on top of the water hoses
or the electricity supply cable.
The appliance must be connected to the water supply network
using new hoses.
Do not use old hoses.
The water inlet and outlet hoses and the electricity supply cable
may be positioned towards the right or the left in order to achieve
the best possible installation.
2
All manuals and user guides at all-guides.com
*
Connecting the water inlet hose
• To a suitable cold water connection point: before attaching the
hose, run the water until it is perfectly clear so that any impurities
that may be present in the water do not clog the appliance;
after performing this operation, screw the inlet hose tightly
onto a tap with a ¾ gas threaded connection.
• To a suitable hot water connection point: your dishwasher
may be supplied with hot water from the mains supply (if you
have a central heating system with radiators) provided that it
does not exceed a temperature of 60°C.
Screw the hose to the tap as described for connection to a
cold water supply.
If the inlet hose is not long enough, contact a specialist store
or an authorised technician ( see Assistance ).
The water pressure must be within the values indicated in the
Technical data table ( see adjacent information ).
The hose should not be bent or compressed.
Connecting the water outlet hose
Connect the outlet hose (without bending it) to a drain duct
with a minimum diameter of 4 cm.
The outlet hose must be at a height ranging from 40 to 80
cm from the floor / surface where the dishwasher rests (A).
Before connecting the water outlet hose to the sink drain,
remove the plastic plug (B).
Anti-flooding protection
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the water supply
in the event of anomalies or leaks from inside the appliance.
Some models are also equipped with the supplementary safety
*
device New Acqua Stop
, which guarantees anti-flooding
protection even in the event of a supply hose rupture.
WARNING: HAZARDOUS VOLTAGE!
Under no circumstance should the water inlet hose be cut as it
contains live electrical parts.
*
Only available in selected models.