Safety Advice; Cleaning Instructions - Palram SkyLight Shed 6x3 Instrucciones De Montaje

IMPORTANT
Please read these instructions carefully before you start to assemble this product
.
Please
carry out the
steps in
the order
set
out
in
these instructions.
Keep
these instructions
in
a
safe
place for future
reference.
Safety Advice
For
safety purposes we strongly recommend the product to be assembled by at least two people.
Some parts may have sharp edges. Please be careful
when handling components. Always wear gloves,
eye
protection, and long sleeves when assembling or performing
any
maintenance
on
your product.
Do
not attempt to assemble the product
in
windy or wet conditions.
Do not attempt to assemble the product if you are tired, have taken drugs,
medications or alcohol, or if you are prone to dizzy
spells.
Dispose
of
all plastic bags safely
-
keep them away from children's reach.
Keep
children away from the assembly
area.
When using
a
stepladder
or
power tools, make sure that
you are
following
the manufacturer's safety advice.
Do
not climb or stand on the
roof.
Do
not hang or lay on the profiles.
Heavy
articles should not
be leaned against
the
poles.
Keep
roof
and
gutters
clear
of
snow,
dirt
& leaves.
Heavy snow load on the roof
can
make it unsafe to stand below or nearby.
Do
not lean against or push the product during construction.
Hot items such
as
recently used grills,
blowtorches
etc.
must not
be
stored inside the product.
Note:
This
product must
be
anchored on to
a
leveled surface and solid foundation to
ensure its
stability.
Make sure
that
screws and anchors are
compatible with foundation
type. Make sure
that there
are no
obstructions between the
assembly area and
the final position.
Cleaning Instructions
In
order to
clean
the product,
use
a
mild detergent solution and rinse with cold
clean water.
Do not use acetone, abrasive cleaners, or other special detergents to clean the panels.
Clean
the product
once assembly
is
complete.
Before
Starting Assembly
Choose your site carefully before beginning assembly.
The ground surface must be perfectly flat and leveled and have
a
solid base such
as
concrete,
asphalt, deck etc.
Complete site preparation before unpacking parts and
beginning
assembly.
Sort
the
parts and check against
the content parts list.
Parts
should be laid out close at hand. Keep
all
small parts (screws etc.)
in
a
bowl
so
they do not get lost.
Please
consult your local authorities if any permits are required prior to constructing the product.
During Assembly
MWhen encountering the information icon, please refer to the relevant assembly step
for additional comments and assistance.
This icon indicates
that the installer should
be
inside the product.
Attention
This icon
indicates that the
11
installer should
be
outside
the product.
Step
2: Place the back wall panel on the shed base panel according to the
stamped serial number
(part #7701).
Door Assembly
Step 26, 27: Note that panels and profiles are connected
in
the right direction and
that profile
holes are placed
correctly
as
illustrated.
Step 29:
Push
aluminum profiles against part #8439 and then
use
Self-Drilling
screws
(#4045) to connect to the profile (diagram
b). No pre holes are needed.
Step 34: Anchor the
shed on
to
a
solid surface
such
as
concrete, asphalt or wood deck;
use
suitable
screws and plugs. (Screws and plugs are
not supplied).
*Tighten
all screws
when completing
assembly.
Do
not tighten
screws and nuts
(411 &
466) until completion
of
assembly process.
These
2
icons indicate if screws'
tightening
is
required or not.
A
Note: Anchoring this product to the ground
is
essential to its
stability
and rigidity.
It is
required to complete this stage
in
order for your warranty to be valid.