Maintenance / Service - Skil RH1-3805 Serie Manual Del Usuario

• Only use the following batteries and chargers with
this tool
- SKIL battery: BR1*31****
- SKIL charger: CR1*31****
• Do not use the battery when damaged; it should be
replaced
• Do not disassemble the battery
• Do not expose tool/battery to rain
Permitted ambient temperature (tool/charger/battery):
•
- when charging 4...40°C
- during operation –20...+50°C
- during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3 Read the instruction manual before use
4 Batteries may explode when disposed of in fire, so do not
burn battery for any reason
5 Store tool/charger/battery in locations where temperature
will not exceed 50°C
6 Do not dispose of electric tools and batteries together
with household waste material
USE
• Combined switch for on/off and speed control A 2 8 9
- control the speed steplessly from zero to maximum by
putting less or more pressure on the trigger
• Charging battery
! read the safety warnings and instructions
provided with the charger
• Removing/installing the battery 2
• Battery level indicator 7
- press the battery level indicator button H to show the
current battery level.
• Changing direction of rotation q
- when not properly set in left/right position, switch A
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
• Changing bits w
! clean and lightly lubricate the SDS+ accessory
before insertion
- pull back locking sleeve C and insert accessory
in SDS+ chuck while turning and pushing it until it
engages; the accessory locks in position automatically
- pull accessory to check that it is locked correctly
- remove accessory by pulling back locking sleeve C
! the SDS+ accessory requires freedom of
movement which causes eccentricity when tool
is off-load; however, the accessory automatically
centres itself during operation without affecting
drilling precision
! when using hex bits, make sure that these hex bits
are at least 75 mm long, or otherwise use shorter
hex bits with hex adapter G
! do not use bits with a damaged shank
• Selecting operating mode e
1 = normal drilling/screwdriving
2 = hammer drilling
! select operating mode only when tool is switched
off and the switch is locked
- the hammer mechanism is activated by applying a
slight pressure on the tool when the drill bit is in contact
with the workpiece
- it takes a short time for the hammer mechanism to
reach full impact power
- best hammer drilling results can be obtained by only a
slight pressure on the tool; drilling performance will not
improve by applying more pressure on the tool
• Battery protection
Switches off the tool or prevents the tool from being
switched on, when
- the load is too high
- the battery temperature is not within the allowable
operating temperature range of -20 to +50°C
- the lithium-ion battery is nearly empty (to protect
against deep discharge)
! do not continue to press the on/off switch after the
tool is switched off automatically; battery may be
damaged
• LED-light E r
- LED-light E automatically lights on when activating
switch A 2
• Holding and guiding the tool t
! while working, always hold the tool at the grey-
coloured grip area(s)
- keep ventilation slots F 2 uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
APPLICATION ADVICE
• Use the appropriate bits y
! only use sharp bits
• For drilling with non SDS drill bits in wood, metal and
plastic, use an adapter (not standard included) u
! clean and lightly lubricate the SDS+ accessory
before insertion
- pull back locking sleeve C 2 and insert adapter
in SDS+ chuck while turning and pushing it until it
engages; the adapter locks in position automatically
- pull adapter to check whether is it locked correctly
- set switch D 2 to normal drilling (only activate when
tool is switched off and the switch is locked)
• When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
• When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking
of the wood
• Splinterfree drilling in wood i
• Dustfree drilling in walls o
• Dustfree drilling in ceilings p
Drilling in tiles without skidding a
•
• For more information see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use
• Always keep tool clean (especially ventilation slots F 2 )
! remove battery from tool before cleaning
If the tool should fail despite the care taken in
•
manufacturing and testing procedures, please send the
tool undismantled together with proof of purchase to your
dealer.
• Be aware that damage due to overload or improper
handling of the product will be excluded from the
warranty (for the warranty conditions please ask your
dealer).
11