BEGLEC JB Systems Light iMove 5S ELC Manual De Instrucciones página 5

ENGLISH
4. REMOTE CONTROLLER INPUT: connect the optional CA-8 remote to the 1/4" microphone jack to
control the unit for stand by, function and mode
5. SENSITIVITY: To adjust the sound sensitivity.
6. MICROPHONE: To receive audio signal for sound activation.
7. DMX INPUT/OUTPUT: For DMX512 link, use 3-pin XLR plug cable to link the unit together.
MAIN MENU:
 To select any of the pre-set
functions, press the MENU button
up to when the required one is
shown on the display.
 Select the function with
the
ENTER button. The display will
blink.
 Use DOWN and UP button to
change the mode.
 Once the required mode has
been selected, press the ENTER
button to select. After 8 seconds
the display will automatically
return to the main functions
without any change. To go back
to the functions without any
change press the MENU button.
The main functions are shown on
the right.
DMX512Address
Setting
Used to set the starting address
in a DMX setup.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the
display starts blinking.
 Use DOWN and UP buttons to
change the DMX512 address.
 Once the correct address shows
on the display, press the ENTER
button to save it.
(or automatically return to the
main functions without any change
after 8 seconds)
To go back to the functions without any change press the MENU button again.
Show Mode
Used to choose the Show mode when used in standalone or master/slave mode.

Press the MENU button until is showing on the display.

Press the ENTER button, the display starts blinking.

Use DOWN and UP button to select the
(show 4) mode.

Once the right mode shows on the display, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
JB SYSTEMS®
OPERATION MANUAL
(show 1) or (show 2) or (show 3) or
5/68 iMove 5S
ENGLISH
Show 1 mode - Fixture is placed on the floor. Tilt movement angle 210°.
Show 2 mode - Fixture is fixed under ceiling. Tilt movement angle 90°.
Show 3 mode - Fixture is placed on the speaker,
The spot is always projecting to the audience's direction; i.e in front of the stage. Pan movement
angle (left to right to left ): 160°. Tilt movement angle: 90° ( 60° above horizon; 30° below
horizon.)
Show 4 mode - Fixture is fixed under ceiling.
The spot is mainly projecting in front of the stage. Pan movement angle ( left to right to left ) :160°.
Tilt movement angle: 90° ( vertically, front 75°; back 15° )
Slave Mode
Used to make the slave unit work in opposite to the master or to work in complete sync.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
(normal) or
 Once the mode has been selected, press the ENTER button save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Blackout Mode
Blackout mode: when no DMX-signal is detected, the unit goes in blackout and waits for the DMX-
signal.
No blackout mode: when no DMX-signal is detected, the unit automatically switches to standalone
mode.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
(yes blackout) or
 Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Color Mode
Normal: only full colors can be selected.
Split colors: you can select full colors and 2 colors that are next to each other on the color wheel.
 Press the MENU button unitl
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
(normal) or
 Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Pan Inversion
Normal: Panning movement is not inversed.
Pan inversion: Panning movement is inversed
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
(normal) or
 Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
JB SYSTEMS®
OPERATION MANUAL
(2 light show) mode.
(no blackout) mode.
(split color) mode.
(pan inversion) mode.
6/68 iMove 5S